CONTA-CLIP SMS-MULTI I/O User Manual

Conta-electronics

CONTA-ELECTRONICS

=====

SMS

SMS----MULTI

MULTI

MULTI----IO

=====

=====GSM controllable I

GSM controllable I

GSM controllable I////O module

O module

Further information:

www.conta-clip.com

Cat. No.: 95120.4

Further information:

www.conta-clip.com

Electrical specifications

Quick Start Guide

The SMS-MULTI-IO is a compact remote telemetry and
control system.

The various I/Os are monitored and controlled by SMS
communication through the GSM network.
The SMS-MULTI-IO can also be integrated into a modbus
driven application.
Every defined input status change (digital) or reached level
(analog) sends a SMS notification to a selected group of
users. The outputs are set by simply sending an SMS to the
SMS-MULTI-IO.
I/Os are defined by an easy to use PC configuration
program.

Order Information

Order Information
type
cat. no.
Weight

Input / Output Data

* of measured value

8 multifunctional analog/dig. inputs
resolution / accuracy (V / I / RTD)
input resistance (0..10V)
input resistance ( 0(4)..20mA)
reference resistance (RTD)
input current (Dig.input (10-30VDC))
UI throughput speed
input thresshold Dig.input

2 analog outputs
load resistance / current per channel
resolution / conversion error

4 relay outputs
rated / inrush current (ohmic load)
max. power rating
life span @ 23°C and ohmic load
max. switching frequency
contact material / test voltage

GSM Data

GSM Data
Frequency (MHz)
Sensitivity
Transmit power
Antenna

General Data

General Data
module power supply
module current (max)
operating / storage temperature
CE marking

conductor cross section / strip length
mounting / installation position
module size LxWxH (TS 35 / direct)
insulating material / flammability class
protection degree (DIN 40050)
installation guidelines

SMS-MULTI-IO.dab.xls 07-10-2010

resistor type: plug-in (Rt), sensor dependant ± 0,1% (5k11 for Ni/Pt100(0) -40..+120°C)(resistors not included)

LO < 3,5V / HI > 5,5V

> 1kOhm / < 10mA

10mV / ± (30mV + 0,5%*)

8A / 12A

2 x NO contact, 2x CO contact, 250V~

6 min

-1

at rated current, 1200 min

-1

at no load

–106 dBm (typical)

16039.2

Housing: noryl. Terminals: polyamid 6.6 V0 / UL94-V0

0,2 - 2,5 mm² screw clamp connection / 6mm

DIN-rail TS35 or direct mounting / any

88 x 95 x 60 / 58 mm

0..10V / 0(4)..20mA / RTD / 24VDC

Electrical: at rated / 2A load: 1 x 10

/ 4 x 10

cycles. Mechanical: 30 x 10

cycles

50 Ohm impedance, SMA connector

Class 4 (2W@850/900 MHz), Class 1 (1W@1800/1900 MHz)

285gr

for mounting-, wiring- and installation instructions, see Manual

AgNi 0,15 / 4kV

275 mA DC

IP 20

20..28V DC

850/900/1800/1900

R&TTE 1999/5/EC according requirements ETSI EN 301-511 V9.0.2

EMC Directive 2004/108/EC, according requirements of EN 55011 and EN 61326-1

min. @10V: 46uA / typ. @24V: 2,6mA / max. @30V: 3,9mA (the resistor plug-in socket must be empty)

500ms

SMS-MULTI-IO

Low Voltage Directive (LVD) 2006/95/EC, according requirements of EN 50178

-20°C…+50°C / -20°C…+70°C

2000VA

10mV / ±(10mV+0,3%*); 20uA / ±(20uA+0,4%*); NI1000: 0,1°C / ±2,5°C or PT100(0): 0,1°C / ±2,5°C

0…10V DC

resistor type: fixed, 220 kOhm (the resistor plug-in socket must be empty)

resistor type: plug-in (Ri), 50 Ohm ± 0,1%. (resistor not included)

Features:

• 8 multi-functional analog/digital inputs: 0..10V,
0(4)..20mA, RTD (eg. Ni1000, PT1000, PT100), 24VDC

• 2 Analog outputs: 0...10V DC

• 4 relay outputs 2x NO contact, 2x CO contact 250V/8A

• LED status indication for all I/Os (except analog inputs)

• SMS status report for all I/Os

• SMS control for all outputs

• SMS notification on status change at inputs

• SMS notification on power up and power loss

• Easy to use PC configuration program

SMS-MULTI-IO quick start guide rev1 .fl_EN.doc