BINDER BD 23 - Manual (Page 51)

BD / ED / FD (E2) 02/2015 page 51/63
Unit size FD 23 FD 53 FD 115 FD 240
Temperature data
Temperature range, 5 °C above ambient
up to
°C / °F 300 / 572 300 / 572 300 / 572 300 / 572
Temperature fluctuation at 150 °C / 302 °F ± K 0.3 0.3 0.3 0.3
Temperature
uniformity
(variation 1)
at 70 °C / 158 °F ± K 0.8 0.8 0.7 0.8
at 150 °C / 302 °F ± K 2.2 2 1.8 2
at 300 °C / 572 °F ± K 4.3 3.7 3.9 4.3
Heating up time 2)
to 70 °C / 158 °F Min 7 7 7 11
to 150 °C / 302 °F Min 22 24 28 24
to 250 °C / 482 °F Min 45 60 49 50
Recovery time
after door was
open for 30 sec
2)
at 70 °C / 158 °F Min 2 2 2 2
at 150 °C / 302 °F Min 4 5 5 6
at 300 °C / 572 °F Min 9 9 12 13
Ventilation data
Air change
at 70 °C / 158 °F x/h 59 59 29 19
at 150 °C / 302 °F x/h 64 64 32 20
at 300 °C / 572 °F x/h 53 53 26 18
Electrical data
IP system of protection acc. to EN 60529
IP 20 20 20 20
Nominal voltage (±10%) 50/60 Hz V 230 1N~ 230 1N~ 230 1N~ 230 1N~
Nominal power kW 0.8 1.20 1.60 2.70
Power plug shock proof plug
Unit fuse
5x20mm / 230V / time-lag M
Amp
10
external
10
external
10
external
16
external
Energy
consumption
at 70 °C / 158 °F Wh/h 145 172 230 370
at 150 °C / 302 °F Wh/h 300 429 544 850
at 300 °C / 572 °F Wh/h 720 951 1100 1400
Installation category acc. to IEC 61010-1 II II II II
Pollution degree acc. to IEC 61010-1 2 2 2 2
Electrical connection data FD-UL acc. to cUL standard (for USA and Canada):
Unit size FD 23-UL FD 53-UL FD 115-UL FD 240-UL
Electrical data
Nominal voltage (±10%) 60 Hz
V 115 1N~ 115 1N~ 115 1N~ 208 3N~
Nominal power kW 0.80 1.20 1.60 2.70
Nominal current Amp 7.0 10.5 14.0 11.2
Power plug NEMA 5-15P 5-20P 5-20P L21-20P
Unit fuse
6,3 x 32 mm / 250V / super time-lag TT
Amp
12,5
external
16
external
16
external
3 x 16
internal
Legend: 1) without outer glass door 2) up to 98 % of the set value
All technical data is specified for unloaded units with standard equipment at an ambient temperature of
+25 °C / 77 °F and a power supply voltage fluctuation of ±10. The temperature data is determined in
accordance to BINDER factory standard following DIN 12880, observing the recommended wall
clearances of 10 % of the height, width and depth of the inner chamber. Technical data refer to 100% fan
speed.
All indications are average values, typical for units produced in series. We reserve the right to
change technical specifications at any time.
If the cabinet is fully loaded, the specified heating up times may vary according to the load.