Denon AVR-3802 - Manual (Page 30)

30
ENGLISH
1
2
3
4
5
6
7
VIDEO GAME
ROCK ARENA
JAZZ CLUB
MONO MOVIE
(NOTE 1)
MATRIX
WIDE SCREEN
5CH/7CH STEREO
Use this to enjoy video game sources.
Use this mode to achieve the feeling of a live concert in an arena with reflected sounds coming
from all directions.
This mode creates the sound field of a live house with a low ceiling and hard walls. This mode
gives jazz a very vivid realism.
Select this when watching monaural movies for a greater sense of expansion.
Select this to emphasize the sense of expansion for music sources recorded in stereo. Signals
consisting of the difference component of the input signals (the component that provides the
sense of expansion) processed for delay are output from the surround channel.
Select this to achieve an atmosphere like that of a movie theater with a large screen. In this
mode, all signal sources are played in the 7.1-channel mode, including Dolby Pro Logic and Dolby
Digital 5.1-channel sources. Effects simulating the multi surround speakers of movie theaters are
added to the surround channels.
In this mode, the signals of the front left channel are output from the left surround channel, the
signals of the front right channel are output from the right surround channel, and the same (in-
phase) component of the left and right channels is output from the center channel. This mode
provides all speaker surround sound, but without directional steering effects, and works with any
stereo program source.
Depending on the program source being played, the effect may not be very noticeable.
In this case, try other surround modes, without worrying about their names, to create a sound field suited
to your tastes.
NOTE 1: When playing sources recorded in monaural, the sound will be one-sided if signals are only input to
one channel (left or right), so input signals to both channels. If you have a source component with only
one audio output (monophonic camcorder, etc.) obtain a “Y” adaptor cable to split the mono output
to two outputs, and connect to the L and R inputs.
NOTE:
Only the DIRECT and 5CH/7CH STEREO modes can be used when playing PCM signals with a sampling
frequency of 96 kHz (such as from DVD-Video discs that contain 24 bit, 96 kHz audio). If such signals are
input during playback in one of the other surround modes, the mode automatically switches to DIRECT.
11 DSP SURROUND SIMULATION
Surround modes and their features
• The AVR-3802 is equipped with a high performance DSP (Digital Signal Processor) which uses digital signal
processing to synthetically recreate the sound field. One of seven preset surround modes can be selected
according to the program source and the parameters can be adjusted according to the conditions in the
listening room to achieve a more realistic, powerful sound. These surround modes can also be used for
program sources not recorded in Dolby Surround Pro Logic or Dolby Digital.
Personal Memory Plus
This set is equipped with a personal memorize function that automatically memorizes the surround modes
and input modes selected for the input different sources. When the input source is switched, the modes set
for that source last time it was used are automatically recalled.
The surround parameters, tone control settings and playback level balance for the different output
channels are memorized for each surround mode.
SURROUND
6.1 / 7.1 SURROUND
5CH / 7CH
STEREO
STEREO DOLBY/DTS
SURROUND DSP
SIMU.
DIRECT
(Remote control unit)
The surround mode switches in the following
order each time the DSP SIMULATION button
is pressed:
WIDE SCREEN MONO MOVIE ROCK ARENA
JAZZ CLUB VIDEO GAME MATRIX
DSP surround simulation
1 Select the surround mode for the input channel.
1 2 3
4 5 6
7 8 9
+10 0 TV/ VCR
C S/C
SKIP
SKIP
ENTER
MEMORY
VOLUME CHANNEL
+
-
+
-
TUNER
VDP
VCR-1
RDS PTY RT
VCR-2 /V.AUX
DVD
TV/DBS
CDR/ TAPE
PHONO CD
SURROUND
OUTPUT TEST TONE SPEAKER
6.1 / 7.1 SURROUND
5CH / 7CH
STEREO
STEREO DOLBY/DTS
SURROUND DSP
SIMU.
DISPLAY
DIRECT
RETURN SETUP
MENU
SHIFT
SURR. PARA. OSD
A/B
MUTING
BAND MODE
TUNING
TUNING
3
2, 4
1
2 Display the surround parameter screen on the monitor.
The screen for the selected surround mode appears. SURR. PARA.
(Remote control unit)
3 Set the parameters.
BAND MODE
TUNING
TUNING
BAND MODE
TUNING
TUNING
(Remote control unit)
4 To end the setting mode, press the surround parameter button again.
NOTES:
• The surround speaker setting can also be changed with the SPEAKER button on the remote control unit.
• When “Default” is selected and the
F courser button is pressed, “CINEMA EQ.” and “D.COMP.” are
automatically turned off, “ROOM SIZE” is set to “medium”, “EFFECT LEVEL” to “10”, “DELAY TIME” to
“30ms” and “LFE” to “0 dB”.
• The “ROOM SIZE” expresses the expansion effect for the different surround modes in terms of the size
of the sound field, not the actual size of the listening room.
• To operate the surround mode and surround parameters from the remote control unit.
SURR. PARA.
(Remote control unit)