English, Setting the digital in assignment – Denon AVR-3802 User Manual

Page 14

ENGLISH

Use the CURSOR buttons to adjust all the speakers to the
same volume.
The volume can be adjusted between –12 dB and +12 dB in
units of 1 dB.

Example: When the volume is set to

–12 dB while the test tone
is being produced from the
subwoofer

SBR

SBL

1spkr

2spkrs

When the surround back speaker setting is set to
“1spkr” for “Speaker Configuration”, this is set to “SB”.

Select “Yes”.

BAND

MODE

TUNING

a. If the “Auto” mode is selected:

Test tones are automatically emitted from the different
speakers.
The test tones are emitted from the different speakers in
the following order, at 4-second intervals the first time and
second time around, 2-second intervals the third time
around and on:

BAND

MODE

TUNING

Flashing

Example: When the volume is set to

–12 dB while the
subwoofer is selected

b. When the “Manual” mode is selected

Use the CURSOR left and right to select the speaker for
which you want to output test tones, then use the
CURSOR up and down to adjust so that the volume of the
test tones from the various speakers is the same.

Flashing

BAND

MODE

TUNING

After the above settings are completed, press the ENTER button.
The “Channel Level” screen reappears.

ENTER

SHIFT

BAND

MODE

TUNING

To cancel the settings, select “Level Clear” and “Yes” on the “Channel Level” screen, then make the
settings again.

The level of each channel should be adjusted to 75 dB (C-weighted, slow meter mode) on a sound level meter
at the listening position.
If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because
adjusting the subwoofer level test tone by ear is difficult, use a well known music selection and adjust for natural
balance.

NOTE:

When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer’s
own volume control.

When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel
level adjustments made will affect ALL surround modes. Consider this mode a Master Channel Level
adjustment mode.
After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the
individual surround modes and adjust channel levels that will be remembered for each of those modes.
Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments
for just that mode will be recalled. Check the instructions for adjusting channel levels within each
surround mode on page 27.
You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5/7 CH
STEREO, DOLBY/DTS SURROUND, WIDE SCREEN, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MONO
MOVIE, and MATRIX.
When using either surround speakers A or B, or when using surround speakers A and B at the same time,
be sure to adjust the balance of playback levels between each channel for the various selections of “A
or B” and “A and B”.

• This setting assigns the digital input jacks of the AVR-3802 for the different input sources.

Setting the Digital In Assignment

At the System Setup Menu select “Digital In Assignment”.

BAND

MODE

TUNING

Switch to the Digital In Assignment screen.

ENTER

SHIFT

Select the digital input jack to be assigned to the input source.
• To select the input source
• To select the digital input jack
Select “OFF” for input sources for which no digital input jacks are used.

If “Yes” is selected for “Default”, the settings are automatically reset
to the default values.

BAND

MODE

TUNING

BAND

MODE

TUNING

NOTES:
• The OPTICAL 3 jacks on the AVR-3802’s rear panel are equipped with an optical digital output jack for

recording digital signals on a CD recorder, MD recorder or other digital recorder. Use this for digital recording
between a digital audio source (stereo - 2 channel) and a digital audio recorder.

• Do not connect the output of the component connected to the OPTICAL 3 OUT jack on the AVR-3802’s rear

panel to any jack other than the OPTICAL 3 IN jack.

• “PHONO” and “TUNER” cannot be selected on the Digital In Assignment screen.

Enter the setting.
The System Setup Menu reappears.

ENTER

SHIFT