Denon AVR-3802 - Manual (Page 19)

19
ENGLISH
If your AV component is not a Denon product or if it cannot be operated using the preset memory, it can be
controlled with the included remote control unit by storing its remote control signals in the remote control unit.
Learning function
1 Press the power ON/SOURCE button and the
OFF button simultaneously.
• “SET UP” appears on the remote control
unit’s display.
OFF ON / SOURCE
2 Press the ENTER button. ENTER
SHIFT
3 Use the D and H cursor buttons to display
“LEARN” on the remote control unit’s display,
then press the ENTER button.
• “SEL MODE” is displayed.
1 2 3
4 5 6
7 8 9
+10 0 TV/ VCR
OFF
TV CD CDR/MD/ TAPE RECEIVER
VCR DBS/CABLE
SKIP
SKIP
ENTER
MEMORY
VOLUME CHANNEL
+
-
+
-
VDP DVD
POWER
REMOTE CONTROL UNIT RC-884
ON / SOURCE
TUNER
VDP
VCR-1
RDS PTY RT
VCR-2 /V.AUX
DVD
TV/DBS
CDR/ TAPE
PHONO CD
SURROUND
INPUT
OUTPUT TEST TONE SPEAKER
6.1 / 7.1 SURROUND
5CH / 7CH
ANALOG EXT.IN MODE
CALL 2 BACKLIGHT CALL 1
STEREO
STEREO DOLBY/DTS
SURROUND DSP
SIMU.
DISPLAY
SYSTEM CALL
DIRECT
RETURN SETUP
MENU
SHIFT
SURR. PARA. OSD
A/B
MUTING
BAND MODE
TUNING
TUNING
1, 5, 8
3, 4
2, 3, 4
BAND MODE
TUNING
TUNING
ENTER
SHIFT
4 Use the D and H cursor buttons to select the
mode for the button to be “learned”, then press
the ENTER button.
• “SELECT KEY” is displayed.
BAND MODE
TUNING
TUNING
ENTER
SHIFT
5 Press the button to be “learned” while
“SELECT KEY” is displayed. “NOW LEARN”
appears.
• “NOT VALID” is displayed if a button that
cannot be “learned” is pressed.
• To cancel, press the power ON/SOURCE
button and the OFF button simultaneously.
OFF ON / SOURCE
6 Point the remote control units directly at each
other and press and hold in the button on the
other remote control unit which you want to
“learn”.
Other remote
control unit
7 “COMPLETE” appears on the remote control
unit’s display and learning is completed.
• “SELECT KEY” is displayed. Other keys can
be “learned” by repeating steps 5 to 7.
8 To cancel the learning mode, press the power
ON/SOURCE button and the OFF button
simultaneously again.
Registering is not possible in the receiver
mode.
OFF ON / SOURCE
The included remote control unit is equipped with a system call function allowing a series of remote control
signals to be transmitted by pressing a single button.
This function can be used for example to turn on the amplifier’s power, select the input source, turn on the
monitor TV’s power, turn on the source component’s power and set the source to the play mode, all at the touch
of a button.
System call
1 Press the power ON/SOURCE button and the
OFF button at the same time. “SET UP”
appears on the remote control unit’s display.
OFF ON / SOURCE
2 Press the ENTER button.
ENTER
SHIFT
3 Use the D and H cursor buttons to display “SYS
CALL” on the remote control unit, then press
the ENTER button.
• Display “SYS MODE” on the remote control
unit’s display.
1 2 3
4 5 6
7 8 9
+10 0 TV/ VCR
OFF
TV CD CDR/MD/ TAPE RECEIVER
VCR DBS/CABLE
SKIP
SKIP
ENTER
MEMORY
VOLUME CHANNEL
+
-
+
-
VDP DVD
POWER
REMOTE CONTROL UNIT RC-884
ON / SOURCE
TUNER
VDP
VCR-1
RDS PTY RT
VCR-2 /V.AUX
DVD
TV/DBS
CDR/ TAPE
PHONO CD
SURROUND
INPUT
OUTPUT TEST TONE SPEAKER
6.1 / 7.1 SURROUND
5CH / 7CH
ANALOG EXT.IN MODE
CALL 2 BACKLIGHT CALL 1
STEREO
STEREO DOLBY/DTS
SURROUND DSP
SIMU.
DISPLAY
SYSTEM CALL
DIRECT
RETURN SETUP
MENU
SHIFT
SURR. PARA. OSD
A/B
MUTING
BAND MODE
TUNING
TUNING
1
7
3, 4, 5
2, 3, 5, 6, 8
BAND MODE
TUNING
TUNING
ENTER
SHIFT
(1) System call buttons
The buttons that can be used for the system call
function are shown on the diagram at the right.
System call signals can be stored at different
buttons according to the mode. System call
signals can be stored at a maximum of 6 buttons
other than the CALL 1 and CALL 2 buttons.
29 successive operations can be set at each of
these buttons.
(2) Storing system call signals
4 When “SYS MODE” is displayed, the remote
control unit’s display switches as shown below
each time the
D and H cursor buttons are
pressed.
BAND MODE
TUNING
TUNING
SYS MODE SYS CALL 1
SYS CALL 2
When “SYS CALL 1” or “SYS CALL 2” is
selected, the signals are stored at the SYSTEM
CALL 1 and CALL 2 buttons (green), regardless
of the mode. When the enter button is pressed,
the button registering mode (step 6) is set.
To register at other buttons, select “SYS
MODE” then press the enter button.
• After “SEL MODE” is displayed on the
remote control unit’s display, the mode last
set is displayed.
1 2 3
4 5 6
7 8 9
+10 0 TV/ VCR
OFF
TV CD CDR/MD/ TAPE RECEIVER
VCR DBS/CABLE
SKIP
SKIP
ENTER
MEMORY
VOLUME CHANNEL
+
-
+
-
VDP DVD
POWER
REMOTE CONTROL UNIT RC-884
ON / SOURCE
TUNER
VDP
VCR-1
RDS PTY RT
VCR-2 /V.AUX
DVD
TV/DBS
CDR/ TAPE
PHONO CD
SURROUND
INPUT
OUTPUT TEST TONE SPEAKER
6.1 / 7.1 SURROUND
5CH / 7CH
ANALOG EXT.IN MODE
CALL 2 BACKLIGHT CALL 1
STEREO
STEREO DOLBY/DTS
SURROUND DSP
SIMU.
DISPLAY
SYSTEM CALL
DIRECT
RETURN SETUP
MENU
SHIFT
SURR. PARA. OSD
A/B
MUTING
BAND MODE
TUNING
TUNING