Delta Electronics Digital Setup Display DVPDU-01 User Manual

Dvpdu-01 digital setup display, Instruction sheet

DVPDU-01 Digital Setup Display

Instruction Sheet

WARNING

Please power down the MPU of the

PLC prior to install the DU-01, which
is connected via a high-density
connector. Also please read the
figures on the right for operation
correctly to prevent damage.

INTRODUCTION

DU-01 Digital Setup Display has two operation modes, TS-01 and
TC-01. The mode selection switch locates at the back of the
DU-01. Factory setting is TS-01 mode. The current operation
mode will be displayed every time when power up.

TS-01

TC-01

Back of the DU-01

1. In

TS-01 mode, DU-01 (specified as TS-01 hereof) has the following functions:

• Read/Write both the internal devices of PLC (e.g. perpetual calendar, bit devices (X, Y, M, S)

and word devices (T, C, D)) and the Control Register (CR) inside the extension units.

• Support the read/write 32-bit data register.

• Set Start-up display and power save mode.

• Monitor the devices.
• If connect the accessory cable to ES-series without perpetual calendar, the Time Display will

start from 00-00-00 calculated by the microprocessor of DU-01 (timing error may occur).

• Give RUN-STOP command to PLC.

2. In

TC-01 mode, DU-01 (specified as TC-01 hereof) has the following functions for DVP all series:

• Read/write the program P, data register D and file register F from PLC.
• Copy program and data.

• Support the PLC password protection.

Overview of the Product - Names of Parts

P: program area indication
(TC-01)

2 W: write (WR) indication (TC-01)

3 R: read (RD) indication (TC-01)

4 “In communication” indication

D: Data Register indication
(TC-01)

F: File Register indication
(TC-01)

CR: Control Register indication
(Extension Module)

8 ER: Error message display

9 Display

Area

10 Enter button

indication

K (Decimal), H (Hexadecimal)
indication

Contacts & coils of timer /
counter indications

Word devices T, C, D, DD

(32-bit)

indication

14 Bit devices X, Y, M, S indication

15 Digit backspace / Run (TC-01)

16 Back to previous status

17 Enter number or select device

18 Confirm

ESC

5
6
7
8

DU-01

19 Enter number or select device

INSTALLATION & WIRING

1. Direct mounting to the expansion slot in the MPU of

the EP/EH series

Please power down the PLC MPU prior to install the DU-01,

which is connected via a high-density connector. Also please
refer to the figures above for proper operation. Put the
face-up DU-01 slantly in the extension slot, then push it down
in arrow direction. DO NOT push it down vertically to prevent
damage.

2. Connecting to DVP

series PLC via accessory
cable

(No need to shut down the MPU)

TS-01 OPERATION

Switch DU-01 to TS-01 mode. (Please see the back of the DU-01)

2. Main

Process

ESC

Time Mode

Press and hold for 3 sec.

Auto Save

Confirm & update time

Operation Mode

Display
Selection

No Save

YY-MM-DD

HH-MM-SS

Device

Selection

Device Selection

X, Y, M, S

T, C, D

DD(32-bit)

ESC

Device
Monitor

Bit
Device

Word
Device

Device confirm

Number Selection

Specify a number

Force On/Off setting

Specified No.
Display

Enter Set Value

Enter a number

Number Selection

Press

to complete entering & return

Monitor status of 8 consecutive
devices from the specified number

Press and hold for 3 sec.

Start-up display mode setting (press

buttons simultaneously)

Any mode*

Sleep mode

Monitor

Mode

Press +
Until shows

Time & device

content

Sleep mode activated if no button is pressed
within 30 seconds

*Note: not include system operation mode setting

Please see the back page for detail information about the process of each mode.

TC-01 OPERATION

1. Switch the DU-01 to TC-01

mode (please see the back of
the DU-01), and select RD (to
read P, D and F in the MPU of
PLC) or WR (to write the data
in P, D, F of DU-01 to the MPU
of PLC).

TC-01

Indication of the connected MPU model

Indication of internal data storage model

Note: P: Program, D: Data register, F: File register

2. TC-01 Password Key Setting

Password key setting of TC-01 can be set via WPLSoft. The purpose is to read/write to the key-locked
PLC as long as the password setting matches with the one in PLC. To unlock the password key
setting, please use WPLSoft as well.

a) Password Key Setting

In RD or WR mode, press ESC button and hold for 3 seconds or
more to enter password setting. See the figure on the right:

Open WPLSoft [Setting] [TC-01 password key setting].
Select [Enter TC-01 password key], and operate as instructed.

After setting, display shows the figure on the right. (KEY SET),
then press ESC to exit.

b) TC-01 has password key setting, therefore, only if the PLC has no password protection or with the

same password with TC-01 can process the writing. It also writes the password to the PLC for
added protection.

c) Password key clear (KEY CLR): Same as the operation above. Open WPLSoft, select [TC-01

password key clear], and operate as instructed.

3. Clear P, D, F of TC-01: select the device (P, D or F) to be cleared, press

simultaneously,

then press ESC.

4. RD mode description:

RD read mode

P,D,F selection

P(Program)

D (Data Register)

F (File Register)

Reading P (Program).

You can press ESC to

pause reading.

Setting reading range.

(default start & end

addresses are latched

area range. User can

re-set it.)

Reading F (file register)

You can press ESC to

pause reading.

Enter start address

Finish reading

Finish reading.

d1EC is the CHKSUM

of writing program

2746 is the CHKSUM

of writing data

Enter end address

Reading processing...
You can press ESC to

pause reading.

Confirm
Device