Delta Electronics Network Device IFD9506 - Manual

Warning
This instruction sheet only provides introductory information on electrical specification, installation and wiring.
Switch off the power before wiring. DO NOT touch any terminal when the power is switched on.
IFD9506 is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity,
electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key
or specific tools are required to open the enclosure) in case danger and damage on the device may occur.
Introduction
Features
1. Auto-detects 10/100 Mbps transmission speed; MDI/MDI-X auto-detection.
2. The monitor table temporarily stores the monitored data for the user to fast save or acquire the data.
3. Supports Modbus TCP protocol (supports Master and Slave mode)
4. Able to send out emails after being triggered.
5. The station address, RS-485 communication format and baud rate can be set up externally.
6. The communication parameters can be set up through Web.
Product Profile & Outline
9
1 Communication ports: RS-485,
Ethernet, RS-232
2 Power indicator
3 Address switch
4 Data format/baud rate switch
5 Digit display
6 RS-485 indicator, Reset button,
Ethernet indicator
7 Module name
8 RS-485 connector, digital input points,
power input point, earth point
9 DIN rail connector
Specifications
Ethernet Interface
Interface RJ-45 with Auto MDI/MDIX
Transmission method Ethernet Type II
Transmission cable Category 5e, 100m (Max)
Transmission speed 10/100 Mbps Auto-Detection
Network protocol ICMP, IP, TCP, UDP, DHCP, SMTP, MODBUS OVER TCP/IP, Delta
Configuration
ENGLISH
RS-485 Connector
Interface RJ-11
Transmission method RS-485
Transmission speed 110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200
Communication format Stop bit: 1,2 Parity bit: None, Odd, Even Data bit: 7,8 ASCII/RTU
Communication
protocol Modbus, User Define
RS-232 Connector
Interface Mini Dim
Transmission method RS-232
Transmission speed 110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200
Communication format Stop bit: 1,2 Parity bit: None, Odd, Even Data bit: 7,8 ASCII/RTU
Communication
protocol Modbus, Delta Configuration, User Define
Transmission cable DVPACAB215 / DVPACAB230 / DVPACAB2A30
Terminal Block
Interface Feed-through terminal 10PIN
Transmission method RS-485
Transmission distance 1,200m
Transmission speed 110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200
Communication format Stop bit: 1,2 Parity bit: None, Odd, Even Data bit: 7,8 ASCII/RTU
Communication
protocol Modbus, User Define
Electrical Specifications
Power voltage 24V DC (-15% ~ 20%) supplied by feed-through terminal
Power consumption 3W
Insulation voltage 500V
Weight 140g
Environment
Noise immunity
ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge
EFT (IEC 61131-2, IEC 61000-4-4): Power Line:±2KV, Digital Input: ±2KV,
Communication I/O: ±2KV
RS (IEC 61131-2, IEC 61000-4-3): 80MHz ~ 1GHz, 10V/m. 1.4GHz ~ 2.0GHz,
10V/m
Conducted Susceptibility Test (EN61000-4-6, IEC61131-2 9.10): 150KHz ~
80MHz, 3V/m
Surge Test (Biwave IEC61132-2, IEC61000-4-5):
Power line 0.5KV DM, Ethernet 0.5KV CM, RS-485 0.5KV CM
Operation/storage Operation: 0ºC ~ 55ºC (temperature), 50 ~ 95% (humidity), pollution degree 2
Storage: -25ºC ~ 70ºC (temperature), 5 ~ 95% (humidity)
Vibration/shock
immunity International standards: IEC61131-2, IEC68-2-6 (TEST Fc)/IEC61131-2 & IEC
68-2-27(TEST Ea)
Certificates
Installation
Dimension
Unit: mm
Address Switch
Switch setting Content
01 … F7 Valid Modbus communication address
Data Format Switch
Switch setting Format Switch setting Format
0 7-N-1 8 7-N-2
1 8-N-1 9 8-N-2
2 7-O-1 A 7-O-2
3 8-O-1 B 8-O-2
6 7-E-1 E 7-E-2
7 8-E-1 F 8-E-2
Baud Rate Switch
Switch setting Baud rate (bps) Switch setting Baud rate (bps)
1 110 7 4,800
2 150 8 9,600
3 300 9 19,200
4 600 A 38,400
5 1,200 B 57,600
6 2,400 C 115,200
RJ-11 PIN Definition
PIN Signal Definition PIN Signal Definition
1 -- N/C 4 D- Negative pole for data
2 -- N/C 5 GND Ground
3 D+ Positive pole for data 6 -- N/C
RJ-45 PIN Definition
PIN Signal Definition PIN Signal Definition
1 Tx+ Positive pole for data
transmission 5 -- N/C
2 Tx- Negative pole for data
transmission 6 Rx- Negative pole for data
receiving
3 Rx+ Positive pole for data
receiving 7 -- N/C
4 -- N/C 8 -- N/C
RS-232 PIN Definition
PIN Signal Definition PIN Signal Definition
1 -- N/C 5 Tx Transmission data
2 -- N/C 6 -- N/C
3 -- N/C 7 -- N/C
4 Rx Reception data 8 GND Ground
Feed-through Terminal PIN Definition
PIN Signal Definition
1 SG Ground of signal
2 D- Data-
3 D+ Data+
4 X2 Digital input 2
5 X1 Digital input 1
6 X0 Digital input 0
7 S/S Ground of digital input
8 24V +24V
9 0V 0V
10 -- Earth ground
LED Indicators & Trouble-Shooting
There are 3 LED indicators and a digital display on IFD9506. POWER indicator displays the status of the
working power. RS-485 and LINK/ACT indicators display the connection status of the communication. The
digital display shows the address of and errors in IFD9506 and the error messages from the slave.
POWER LED
LED status Indication How to correct
OFF Working power is abnormal Check if the working power of IFD9506 is normal.
Green light ON Working power is normal --
RS-485 LED
LED status Indication How to correct
OFF No communication or RS-485
connection is abnormal. 1. If the LED is off during the communication, check if the RS-485 in
IFD9506 is normally connected.
2. Check at least 1 node on the network is communicating normally.
Constantly ON Abnormal RS-485 connection Switch D+ and D-
Green light
flashes RS-485 connection is normal. --
LINK/ACT LED
LED status Indication How to correct
OFF No power, or no network
connection
1. Check the power of IFD9506 and make sure the network
connection is normal.
2. Re-power IFD9506. If the error still exists, send your IFD9506
back to the factory for repair.
Green light ON The connection is normal, but no
data transmission. --
Green light
flashes The data transmission is normal. --
Codes in Digital Display
Code Indication How to correct
01 ~ F7 The node address of IFD9506 when
in normal operation --
F0 Returning to default setting --
F1 IFD9506 is booting --
F2 Working power in low voltage Check if the working power is normal.
F3 Internal memory error
1. Re-power IFD9506. If the error still exists, try step 2.
2. Reset IFD9506. If the error still exists, send it back to the factory
for repair.
F4 Internal error caused by
manufacturing in the factory 1. Re-power IFD9506. If the error still exists, try step 2.
2. Reset IFD9506. If the error still exists, send it back to the factory
for repair.
F5 Network connection error Check if IFD9506 is normally connected to the network.
F6 Full number of devices connected in
the network Check if the number is too much.
F7 UART setting error. Check if the RS-485, RS-232 communication format is correct.
E1 Alarm 1 triggered Check Alarm Input Point 1.
E2 Alarm 2 triggered Check Alarm Input Point 2.
E3 Alarm 3 triggered Check Alarm Input Point 3.
01 Incorrect MODBUS function Check if the Modbus instruction is correct.
02 Incorrect address Check if the Modbus instruction is correct.
03 Incorrect data Check if the Modbus instruction is correct.
04 CRC error
1. Check if IFD9506 and RS-485 is connected normally.
2. Check if the series transmission speed is consistent with that of
other nodes on the network.
0B No response from the station
1. Check if IFD9506 and RS-485 is connected normally.
2. Check if the series transmission speed is consistent with that of
other nodes on the network.
注意事項
此安裝手冊只提供電氣規格、一般規格、安裝及配線等。
配線時請務必關閉電源，請勿在上電時觸摸任何端子。
本機為開放型 (OPEN TYPE) 機殼，因此使用者使用本機時，必須將之安裝於具防塵、防潮及免於電擊∕
衝擊意外之外殼配線箱內。另必須具備保護措施（如：特殊之工具或鑰匙才可打開），防止非維護人員操作
或意外衝擊本體，造成危險及損壞。
產品簡介
功能特色
1. 自動偵測 10/100 Mbps 傳輸速率，MDI/MDI-X 自動偵測。
2. 提供 Monitor table 可暫存監控的資料，讓使用者快速存取。
3. 支援 Modbus TCP 協定 (支援 Master 和 Slave 模式)。
4. 經觸發後發送電子郵件。
5. 可由外部設定站號、RS-485 通訊格式、鮑率。
6. 可由 Web 設定通訊參數。
產品外觀
1 通訊口 RS-485, Ethernet,
RS-232
2 電源指示燈
3 站號設定開關
4 通訊格式、通訊速率設定開關
5 數位顯示器
6 RS-485 指示燈、Reset 按鍵、
Ethernet 指示燈
7 模組名稱
8 端子台 RS-485 連接器、數位輸入
點、電源輸入、大地 9
9 DIN 軌連接器
功能規格
Ethernet 連接器
接頭 RJ-45 with Auto MDI/MDIX
傳輸方式 Ethernet Type II
傳輸電纜 Category 5e, 100 公尺 (Max)
傳輸速率 10/100 Mbps Auto-Detection
網路協定 ICMP, IP, TCP, UDP, DHCP, SMTP, MODBUS OVER TCP/IP, Delta Configuration
繁體中文
RS-485 連接器
接頭 RJ-11
傳輸方式 RS-485
傳輸速率 110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200
通訊格式 Stop bit: 1,2 Parity bit: None, Odd, Even Data bit: 7,8 ASCII/RTU
通訊協定 Modbus, User Define
RS-232 連接器
接頭 Mini Dim
傳輸方式 RS-232
傳輸速率 110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200
通訊格式 Stop bit: 1,2 Parity bit: None, Odd, Even Data bit: 7,8 ASCII/RTU
通訊協定 Modbus, Delta Configuration, User Define
傳輸電纜 DVPACAB215 / DVPACAB230 / DVPACAB2A30
端子台連接器
接頭 歐式端子台 10PIN
傳輸方式 RS-485
傳輸距離 1,200m
傳輸速率 110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200
通訊格式 Stop bit: 1,2 Parity bit: None, Odd, Even Data bit: 7,8 ASCII/RTU
通訊協定 Modbus, User Define
電氣規格
電源電壓 24V DC (-15% ~ 20%) 由歐式端子台輸入
消耗電力 3W
絕緣電壓 500V
重量 140g
環境規格
雜訊免疫力
ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge
EFT (IEC 61131-2, IEC 61000-4-4): Power Line:±2KV, Digital Input: ±2KV,
Communication I/O: ±2KV
RS (IEC 61131-2, IEC 61000-4-3): 80MHz ~ 1GHz, 10V/m. 1.4GHz ~ 2.0GHz, 10V/m
Conducted Susceptibility Test (EN61000-4-6, IEC61131-2 9.10): 150KHz ~ 80MHz,
3V/m
Surge Test (Biwave IEC61132-2, IEC61000-4-5):
Power line 0.5KV DM, Ethernet 0.5KV CM, RS-485 0.5KV CM
操作∕儲存環境 操作：0ºC ~ 55ºC（溫度）、50 ~ 95%（濕度）、污染等級 2
儲存：-25ºC ~ 70ºC（溫度）、5 ~ 95%（濕度）
耐震動∕/衝擊 國際標準規範 IEC61131-2, IEC68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27(TEST
Ea)
標準