Placing telephone calls, To place a call, If the call fails to go through – Audiovox CTX-4200 User Manual
Page 9: Automatic redial (nam option), Terminating a call (hanging up), To receive calls, To place a call with a number in the memory
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Display shows Name Tag, Memory address and
Phone Number.
4. Press r#l or ■
[#1; Scroll memory address upward.
@ : Scroll memory address downward.
Example:
Operation
Display
ALPH
5 ALPH
RCL #
vJ _
J
0
H N
1 0 1 1
I
- 1 4
1
5
6
7
8
9
0
J
m
J
A C K
1 0 1 5 1 - 1 7 j 6
5
4
3
2
1
J
A M E
S
1 1 1 5 1 - 1 9 1 8
7
6
5
4
3
J
t
N1
1 9 1 9 1 - 1 8 1 7
6
5
4
3
2
J
0
H N
1 0 1 1 1 - 1 4 1 5
6
7
8
9
0
J
1 M
1 9 i 9 ! - 1 8 1 7
6
5
4
3
2
PLACING TELEPHONE
CALLS
To Place a Call
1. Enter the phone number with the handset on or off
the cradle. The last 15 digits of the dialed number
are displayed on the readout.
Note: After 120 sec., display will return to the
10-digit display mode.
2. If a dialing error is made, press jCLRI, then enter
the phone number again. Pressing |CLR| momen
tarily (less than approx. 0.5 sec.) clears only the
last digit.
3. Press |SND| . The I IN USE | indicator will light. You
may lift the handset either before or after the
called party answers to proceed with your conver
sation.
Note: If assigned in NAM, the phone number can
be pre-set up to 32 digits. However, in this
case it is necessary to confirm with system
operator whether such service is available
or not.
If the Call Fails to Go Through
2
.
If you hear the “reorder” signal, press |END|, then
if there were no dialing errors, press |SND| for
redial. (Redialing with digit keys is not necessary.)
If the “intercept” signal is heard, press |END|, then
redial the correct number.
Automatic Redial (NAM Option)
If the feature of Automatic Redial (NAM Option) is
selected, your unit will automatically make five
attempts to reach the cell site if the first try is not
successful. The | IN USE] indicator will stay on, but
the speaker will be muted for twenty seconds.
This is done so that you do not hear the reorder
signals from the loudspeaker. If you need to termi
nate the automatic redial, press |END|.
Terminating a Call (Hanging Up)
Press |END|, or replace the handset on the cradle.
The I IN
use
] indicator will go out.
If Hands-free is activated in NAM, you have to press
lENDl to terminate a call.
To Receive Calls
1, When the telephone rings, lift the handset or press
|SND| to answer the call. The [ IN USE | indicator
will light.
If the handset is off the cradle when ringing starts,
to answer a call.
2
.
press SND
To Place a Call with a Number in the
Memory
1
.
Press |RCL| , then enter the memory address ( 01
through 99). The last 10 digits of the number will
appear on the readout. If the number is longer
than 10 digits, hold down the second digit of the
memory address (after pressing ¡RCL| )to see the
prefix.
Note: Refer to “To. Recall a Number from
Memory” and “To Review the Prefix” for
more details.
2, Press |SND| . The [ IN USE | indicator will light as
the call is placed.
16
17