Top Flite TOPA0703 - Manual (Page 5)

5
ADDITIONAL ITEMS REQUIRED
REQUIRED HARDWARE AND
ACCESSORIES
In addition to the items listed in the “Decisions You
Must Make” section, following is the list of hardware
and accessories required to fi nish the Top Flite
Giant P-47D ARF. Order numbers are provided in
parentheses.
❏
(2) Dubro #813 1/8" Fuel Line Barb (DUBQ0670)
❏
(1) Dubro #554 X-large Tygon Fuel Line
(DUBQ0427)
❏
(1) R/C foam rubber (1/4" [6mm] (HCAQ1000) or
1/2" [13mm] (HCAQ1050)
❏
Optional Black paint for the plywood radial
engine frame
❏
Propeller and spare propellers suitable for your
engine.
❏
Painted Pilot (GPMA2807)
ADHESIVES AND BUILDING SUPPLIES
This is the list of Adhesives and Building Supplies
that are required to fi nish the Giant P-47D ARF.
❏
1/2 oz. [15g] Thin Pro ™ CA (GPMR6001)
❏
1/2 oz. [15g] Medium Pro CA+ (GPMR6007)
❏
Pro 30-minute epoxy (GPMR6047)
❏
Pro 6-minute epoxy (GPMR6045)
❏
Threadlocker thread locking cement
(GPMR6060)
❏
Mixing sticks (50, GPMR8055)
❏
Mixing cups (GPMR8056)
❏
Epoxy brushes (6, GPMR8060)
❏
Denatured alcohol (for epoxy clean up)
❏
R/C-56 canopy glue (JOZR5007)
❏
Milled fi berglass (GPMR6165)
❏
Masking tape (TOPR8018)
❏
Plan protector (GPMR6167) or wax paper
❏
Drill bits: 1/16" [1.6mm], 5/64" [2mm], 3/32"
[2.4mm], 7/64" [2.8mm], 1/8" [3.2mm], 3/16"
[4.8mm], 1/4" [6.4mm]
❏
Small metal fi le
❏
Stick-on segmented lead weights (GPMQ4485)
❏
Silver solder w/fl ux (STAR2000)
❏
Hobby Heat ™ micro torch (HCAR0755)#1 Hobby
knife (HCAR0105)
❏
#11 blades (5-pack, HCAR0211)
❏
#11 blades (100-pack, HCAR0311)
❏
Sanding tools and sandpaper assortment (see
Easy-Touch
™ Bar Sander section)
❏
Curved-tip canopy scissors for trimming plastic
parts (HCAR0667)
Covering tools
❏
Top Flite MonoKote ® sealing iron (TOPR2100)
❏
Top Flite Hot Sock ™ iron cover (TOPR2175)
❏
Top Flite MonoKote trim seal iron (TOPR2200)
❏
Top Flite MonoKote heat gun (TOPR2000)
OPTIONAL SUPPLIES AND TOOLS
Here is a list of optional tools mentioned in the manual
that will help you build the Giant P-47D ARF.
❏
2 oz. [57g] spray CA activator (GPMR6035)
❏
CA applicator tips (HCAR3780)
❏
CA debonder (GPMR6039)
❏
Builder’s Triangle Set (HCAR0480)
❏
Scale Warbird Template (TOPQ2187)
❏
36" metal ruler (HCAR0475)
❏
Hobbico ® High Precision Diagonal Cutter 5"
(HCAR0630)
❏
Pliers with wire cutter (HCAR0625)
❏
Robart Super Stand II (ROBP1402)
❏
Switch & Charge Jack Mounting Set
(GPMM1000)
❏
Panel Line Pen (TOPQ2510)
❏
Rotary tool such as Dremel
❏
Rotary tool reinforced cut-off wheel (GPMR8200)
❏
Servo horn drill (HCAR0698)
❏
AccuThrow ™ Defl ection Gauge (GPMR2405)
❏
CG Machine™ (GPMR2400)
❏
Laser incidence meter (GPMR4020)
❏
36" bar for incidence meter (GPMR4021)
❏
Precision Magnetic Prop Balancer (TOPQ5700)
IMPORTANT BUILDING NOTES
● Anytime a sheet metal screw is installed in wood,
fi rst install the screw, remove the screw and apply a
couple of drops of thin CA in the hole to harden the
threads. After the CA has cured, reinstall the screw.
● Photos and sketches are placed before the
step they refer to. Frequently you can study photos in
following steps to get another view of the same parts.
● The Giant P-47D ARF is factory-covered with Top
Flite MonoKote fi lm. Should repairs ever be required,
MonoKote can be patched with additional MonoKote
purchased separately. MonoKote is packaged in six-
foot rolls, but some hobby shops also sell it by the
foot. If only a small piece of MonoKote is needed for
a minor patch, perhaps a fellow modeler would give
you some. MonoKote is applied with a model airplane
covering iron, but in an emergency a regular iron could
be used. A roll of MonoKote includes full instructions
for application. Following are the colors used on this
model and order numbers for six foot rolls.
Aluminum (TOPQ0205)
Orange (TOPQ0202)
White (TOPQ0204)
Black (TOPQ0208)
Sapphire Blue (TOPQ0226)
Missile Red (TOPQ0201)