Reznor RXE Parts Manuals - Manual (Page 9)

Form P-X/XE/RX/RXE, P/N 264000, Page 9
Code 76 -
Shutoff
Valves
P/N 196910, 1/2" Shutoff Valve
P/N 1196911, 3/4" Shutoff Valve
P/N 159725, 1" Shutoff Valve
Code 75 -
P/N 3284, Pilot
Shutoff Valve
Reference: For replacement electric gas valve, see Form P-VALVES.
82
89
81
84
Attach with
screws
86
85
Screws
88
87
83
Airflow
Screws
86
87
Airflow
Codes
83-88 -
Directional
Air Baffles
Heat Exchanger and Components
(Numbers in parenthesis are quantities.)
Code 80 - Heat
Exchanger
(less controls)
Burner Rack
& Manifold
Bottom Panel
Code Description Qty 75, 100 125 150, 175 200, 225 250, 300 350 D300, 400
80 Heat
Exchanger
X, CX - Aluminized Steel 1 9895 9855 9817 9779 9743 9707 9514
X, CX - 409 Stainless Steel 1 19429 19430 19431 19432 19433 19434 19435
X, CX - 321 Stainless Steel 1 19438 19439 19440 19441 19442 19443 19444
RX, CRX - Aluminized Steel 1 44301 44304 44307 44310 44313 44316 44319
RX, CRX - 409 Stainless 1 44302 44305 44308 44311 44314 44317 44320
RX, CRX - 321 Stainless 1 44303 44306 44309 44312 44315 44318 44321
81 Burner Rack Slide Rail - All Models 2 9897 9857 9819 9781 9745 9709 9517
82 Burner Rack Back Brace - Al Models 1 9525 9525 9525 9525 9525 9525 9525
83 Bracket for Bottom Baffle Support - P/N 55101 (2) (2) (2) (2) (4) (4) (4)
84 Finger Baffle - P/N 45399 (3) (3) (6) (8) (11) (13) (15)
85 Bottom Baffle Support 1 46478 46484 46489 46494 46499 46504 46509
86 Rear Top Baffle Support 1 55103 55104 55106 55108 55110 55112 55114
87 Rear Top Baffle 1 55228 55229 55231 55233 55235 55237 55239
88 Side Finger Baffle 2 55128 55128 55128 55128 55128 55128 55128
89 Heat Exchanger "V" Tube Baffles - P/N 85727 (4) (5) (7) (9) (12) (14) (16)
See
paragraphs
below for
information
about the
application
of the air
baffles.
Heat Exchanger Directional Air Baffles
Models X, CX, RX, CRX, and packaged systems with these duct furnaces as components are equipped with a heat exchanger
directional air baffle assembly as shown in the illustration above (right top).
When replacing a heat exchanger, check to see if the baffle assembly can be salvaged. If the baffle assembly cannot be salvaged, it
will be necessary to order the parts (Codes 83-88) in the quantities listed and assemble and install replacement baffles. (These parts
must be ordered separately and installed in the field. Baffles cannot be factory installed.)
Models HX, HCX, HRX, HCRX, and packaged systems with "H" or "HC" prefix are equipped with only a rear top baffle support
(Code 86) and a rear top baffle (Code 87) as shown in the illustration above (right bottom). If these parts cannot be salvaged, order
and install replacements.
NOTE: During 2011, the manufacture of HX models was discontinued . A Model X manufactured after discontinuing the "H" models
includes a high CFM conversion kit with instructions in the installation manual. For just the high CFM kit for Model X, order P/N 263308
and follow the instructions in the installation manual Form I-X.