Reznor RV 325 Option - Installation - Heater Stand Assembly - Manual (Page 3)

Form I-OIL-HS, P/N 122407R3, Page 3
Slide the
tube bracket
assemblies
over the
top of each
corner post.
3. Prepare and Install
the Tube Bracket
Assemblies
Tube Bracket
Assembly
1) Be sure surface is clean
and dry.
2) Position label so that it will
be visible from each side of
the heater stand.
3) Attach labels.
4. Install Front and
Rear Support Angles,
Corner Setscrews,
and Angle Stops
Being sure they are in the
correct orientation, attach
a warning label to each
tube bracket assembly.
At the sides of the tank,
connect the posts by slid-
ing a tube bracket down
over the top of each post.
Select and follow the illustrated instructions for the heater being installed.
Instructions for assembling and installing the eight setscrews used in Steps 4 & 5:
Parts: (8) P/N 121596, 1-1/2” lg cap screws and (8) P/N 45550, jam nuts
Assemble: Thread a nut down the length of each screw.
Install: 1) Thread the assembled screw and nut into the threaded hole.
2) Tighten the screw to 190 in-lbs.
3) Finger tighten the jam nut against the tube or sleeve.
4) Using a wrench, tighten the jam nut 1/8 to 1/4 turn.
Corner and Angle Stop
Assembly for Models
RA 110, 140, 235 and
Models OH 95, 140, 190 (4) P/N 121593,
1/2-13x3/4” lg
Hex Hd Cap Screw
(4) P/N 111306
1/2 Lockwasher
(4) P/N 121595
1/2 Flat Washer
(2) P/N
121734
Warning
Label
(one on
each side)
IMPORTANT: Position front and rear support
angles with angle positioned UP as shown here.
(4) P/N 16247
5/16-18x3/4” lg
Hex Hd Cap Screw
(4) P/N 1333,
5/16 Lockwasher (4) P/N 27761,
5/16 Flat Washer
(4) P/N 45550,
1/2-13 Jam Nut
(4) P/N 121596,
1/2-13x1-1/2 lg
Hex Hd Cap Screw
(4) P/N 1035,
5/16-6 Hex Nut
Angle Stop - See
page 2 for selection
and spacing.
(4) P/N 121593,
1/2-13x3/4” lg
Hex Hd Cap Screw
(4) P/N 111306
1/2 Lockwasher
(4) P/N 121595
1/2 Flat Washer
(2) P/N
121734
Warning
Label
(one on
each side)
IMPORTANT: Position front and rear support
angles with angle positioned DOWN as shown
here.
(4) P/N 1333,
5/16 Lockwasher
(4) P/N 45550,
1/2-13 Jam Nut
(4) P/N 1035,
5/16-6 Hex Nut
(4) P/N 121593,
1/2-13x3/4” lg
Hex Hd Cap Screw
(4) P/N 111306
1/2 Lockwasher
(4) P/N 121595
1/2 Flat Washer
(2) P/N
121734
Warning
Label
(one on
each side)
IMPORTANT: Position front and rear support
angles with angle positioned UP as shown
here.
(4) P/N 45550,
1/2-13 Jam Nut
(4) P/N 121596,
1/2-13x1-1/2 lg
Hex Hd Cap Screw
After the Model RV heater is
placed on the stand, use the 3/4”
long F-pointed screws to attach
the angle to the heater bottom.
Attach angle to tube
bracket with a 3/4”
long F-pointed screw.
See page 2 to select
angle and for spacing.
a) Position rails as illustrated,
attaching ends with 3/4” long
screws and washers.
b) At each corner, install the
assembled 1-1/2” cap screw and
jam nut. Follow instructions above.
c) Attach angle stops. See illustra-
tion on page 2 for selection and
the table for spacing (A and B).
Corner and Angle Stop
Assembly for Models
RA 150 and 250
Corner and Angle Stop
Assembly for Models
RV 225 and 325
a)
a)
c)
b)
(4) P/N 16247
5/16-18x3/4” lg
Hex Hd Cap Screw
(4) P/N 27761,
5/16 Flat Washer
(4) P/N 121596,
1/2-13x1-1/2 lg
Hex Hd Cap Screw
Angle Stop - See
page 2 for selection
and spacing.
b)
c)
b)
a)
c)
d)
a) Position rails as illustrated,
attaching ends with 3/4” long
screws and washers.
b) At each corner, install the
assembled 1-1/2” cap screw and
jam nut. Follow instructions above.
c) Attach angle stops. See illustra-
tion on page 2 for selection and
the table for spacing (A and B).
d) After the heater is centered front
to back on the stand, attach each
angle to the heater side using a
3/4” long F-pointed screw.
a) Position rails as illustrated,
attaching ends with 3/4” long
screws and washers.
b) At each corner, install the
assembled setscrew. Follow
instructions above.
c) Attach angle stops. See illustra-
tion on page 2 for selection and
table for spacing (C).
d) After the heater is placed on the
stand, attach each angle to the
heater bottom using a 3/4” long
F-pointed screw.
After a Model RA 150 or 250 heater is
centered front to back on the stand,
use the 3/4” long F-pointed screws to
attach the angles to the heater sides.
d)