Reznor B Option - Installation - Polytube Adapter Instructions - Floor Mount - Manual

Form I-B-PF, Mfg #101694 Rev 4, Page 1
HAZARD INTENSITY LEVELS
1. DANGER: Failure to comply will result in severe
personal injury or death and/or property damage.
2. WARNING: Failure to comply could result in severe
personal injury or death and/or property damage.
3. CAUTION: Failure to comply could result in minor
personal injury and/or property damage. INSTALLATION FORM RZ-NA I-B-PF
Obsoletes RGM 434/436-PF (Version A.3)
®
APPLIES TO: Models B and BE
OPTION CD8 Polytube
Adapter for Blower-
Type Unit Installed at
Floor Level
OPTION DESCRIPTION AND APPLICATION
The polytube adapter option for units installed at floor level not only
adapts blower-type heaters (Sizes 75-400) for use with polytube duct-
work but also includes two sets of legs for floor mounting. This option
is especially designed for use in the greenhouse industry to provide
tempered air at the level where it is most needed. The polytube adapter
is installed on the front of the heater and is equipped with a collar for
attaching the field-supplied polytube.
DANGER
When a unit is installed on the floor, caution
must be taken as to location to prevent any
damage to controls or contact with any
moving parts. Clearances to combustibles
must be strictly observed. Liquids should
never to allowed to be sprayed, poured, or
spilled on the heater controls.
Figure 1 - Polytube Adapter Parts Only in
Option CD8 (parts to floor mount are not
included in this illustration)
DIMENSIONS OF POLYTUBE ADAPTER (inches)
11-9/32
Figure 2
WARNING
Floor-mounted units should not be installed
in areas accessible to non-service personnel.
Various areas of the heater have hot surfaces
as well as the flue gas vent system, which can
cause severe burns. Optional belt and blower
guards (Option AZ6 or CD10) are required.
Top
Left
Side
Right
Side
Bottom
Discharge
Panel Assy
Adjusting
Hardware
Collar
The option 75 100 125 130 165 200 250-300 400
package includes:
Qt
y
P/N Qt
y
P/N Qt
y
P/N Qt
y
P/N Qt
y
P/N Qt
y
P/N Qt
y
P/N Qt
y
P/N
Option CD8 - Pkg P/N 101680 101681 137300 122160 101682 101683 101684 101685
Adapter Side 1 101253 1 101253 1 132066 1 101254 1 101254 1 101254 1 101255 1 101254
Adapter Side 1 101259 1 101259 1 132066 1 101260 1 101260 1 101260 1 101255 1 101260
Adapter Top 1 101266 1 101267 1 132061 1 121548 1 101268 1 101269 1 101270 1 101271
Adapter Bottom 1 101272 1 101273 1 132062 1 121547 1 101274 1 101275 1 101276 1 101277
Discharge Panel Assy 1 101249 1 101249 1 101249 1 101250 1 101250 1 101250 1 101250 1 101250
Discharge Collar Band 1 101499 1 101499 1 101499 1 146463 1 146463 1 146463 1 146463 1 146463
Label 1 101263 1 101263 1 101263 1 101263 1 101263 1 101263 1 101263 1 101263
Adapter Legs 2 101692 2 101692 2 101692 2 101692 2 101692 2 101692 2 101692 2 101692
Blower Support Assy 1 101686 1 101686 1 101686 1 101686 1 101686 1 101686 1 101686 1 101686
Support Angles 2 101691 2 101691 2 101691 2 101691 2 101691 2 101691 2 101691 2 101691
Blower Legs 2 101689 2 101689 2 101689 2 101689 2 101689 2 101689 2 101689 2 101689
Cross Support Brace 1 101690 1 101690 1 101690 1 101690 1 101690 1 101690 1 101690 1 101690
Parts Bag* 1 101693 1 101693 1 101693 1 101693 1 101693 1 101693 1 101693 1 101693
* Parts Bag includes: 56 - P/N 11813, sheetmetal screws #10x1/2" long; 1- P/N 51231, 1/4-20 x 1-1/2 hex head screw;
2-P/N 16246, hex head screw #1/4-20 x 3/4" long; 3 - P/N 7328, hex nuts #1/4-20; 1 - P/N 107246, wing nut #1/4-20
B
Label
C
A
Size 75 100 125 130 165 200 250 / 300 400
A 16-7/32 16-13/32 16-11/l6 16-1/32 16 16-9/16 16-3/4 16-7/32
B 30-7/32 30-7/32 30-7/32 37-7/32 37-7/32 37-7/32 37-7/32 37-7/32
C 10-3/8 10-3/8 10-3/8 13-3/8 13-3/8 13-3/8 13-3/8 13-3/8