Novak Super Sport Plus -- Programming & Gearing (55-1705P-1) User Manual

Page 2

Throttle Profiles 1, 2, 3, 4, & 6 can be independently customized to
fine tune the speed control to feel just the way you like it.
The Super Sport Plus lets you tune the following items:

• Minimum Brake/Drag Brake Percentage--

1 of 10 settings.

• Braking Type--

1 of 2 types of braking styles (standard Constant Force

braking or DRAG BRAKING where braking is applied during neutral).

• Dead Band--

1 of 5 Dead Band settings from 2 to 6%.

• Minimum Drive Percentage--

1 of 5 settings from 2 to 12%.

super sport plus soFtware Flow chart

❊❍❩❊❘●■❍✄✑✑✄✬✾✼✽✸✶✄❚❱❙❑❱❊◗◗▼✷✰

PLEASE NOTE: This page contains optional Advanced Programming items!

• These programming items are STRICTLY OPTIONAL--No further adjustments are required •

(but don’t worry, you can always reset factory defaults by performing the One-Touch programming again, so go ahead & experiment--that’s why the programming is in there, right?)

to customizing profiles

o r

With ESC on & connected to a charged battery (transmitter ON or OFF):
1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER

Remove input signal harness from receiver to avoid radio interference.

2. MAKE SURE THROTTLE PROFILE 1-4 OR 6 IS ACTIVE

If you are not sure what profile is selected, follow the procedures in
‘Throttle Profile Selection’ to check or select desired profile.

Remember that you can not access the Brush-Mode (Profile #6)
without disconnecting the brushless sensor harness from the ESC.

Note: there is no time constraint during selection process of custom parameters.

to adjust minimum brake

(or re-activate std-style brakes)

a.....

PRESS & HOLD SPEED CONTROL’S SET BUTTON

With ESC at neutral, press & hold SET button until the Blue status
LED turns on solid---Release ESC’s SET button once LED is on solid.

b.....

SELECT MINIMUM BRAKE PERCENTAGE

blue

Blue status LED

(1st LED on left)

flashes to indicate active Minimum

Brake setting. Quick press & release to select desired setting.

c.....

PRESS & HOLD SET BUTTON TO STORE SELECTION

When SET button is pressed & held for about 1 second, the new selection
is stored in ESC’s memory--The 4 status LEDs will scroll back & forth to
indicate you are exiting programming & the Red LED will turn on solid

(Red & Green if no transmitter signal present)

--ESC is at neutral & ready to go.

to activate & adjust drag brake

a.....

PRESS & HOLD SPEED CONTROL’S SET BUTTON

With ESC at neutral, press & hold SET button until Blue & Amber
status LEDs turn on solid---Release SET button once LEDs are solid.

b.....

SELECT DRAG BRAKE PERCENTAGE

blue & amber

Blue & Amber status LEDs

(1st & 2nd LEDs on left)

flash to indicate active

Drag Brake setting

(Drag brake setting will be same as Minimum Brake setting)

Quick press & release to change Drag Brake/Minimum Brake setting,
then press & hold SET button for about 1 second to activate drag
braking, store selection into ESC’s memory, and return to neutral.

Note: To re-activate the standard style of braking (no drag brakes during

neutral), repeat Minimum Brake adjustment as described above.

to adjust dead band

a.....

PRESS & HOLD SPEED CONTROL’S SET BUTTON

With ESC at neutral, press & hold SET button until Blue & Green
status LEDs turn on solid---Release SET button once LEDs are solid.

b.....

SELECT DEAD BAND PERCENTAGE

blue & green

Blue & Green status LEDs flash to indicate active Dead Band setting.
Quick press & release to change setting, then press & hold SET
button for about 1 second to store selection and return to neutral.

to adjust minimum drive

a.....

PRESS & HOLD SPEED CONTROL’S SET BUTTON

With ESC at neutral, press & hold SET button until Amber status
LED turns on solid---Release SET button once LED is on solid.

b.....

SELECT MINIMUM DRIVE PERCENTAGE

amber

Amber status LED flashes to indicate active Minimum Drive setting.
Quick press & release to change setting, then press & hold SET
button for about 1 second to store selection and return to neutral.

restoring factory default

restoring factory defaults

Every time you perform the One-Touch Set-Up, the factory default settings are
restored for each of the throttle profiles.

@NEUTRAL

RED or RED & GREEN

MIN. BRAKE

BLUE

DRAG BRAKE

BLUE & AMBER

ACTIVE PROFILE

all LEDs (flashing)

DEAD BAND

BLUE & GREEN

MIN. DRIVE

AMBER

press & hold

quick press

results in red

LED flashing

––––––

indicates

improper

button press

sequence

LEDs roll off

––––

exit programming

continue holding ESC’

s SET button to skip steps here

Setting

(# of flashes)

1 2 3 4 5 6 7 8 9 10

Minimum Brake

(%)

20 25 30 35 40 45 50 55 60 65

Setting

(# of flashes)

1 2 3 4 5 6 7 8 9 10

Drag Brake

(%)

off 25 30 35 40 45 50 55 60 65

Setting

(# of flashes)

Dead Band

(%)

Setting

(# of flashes)

Minimum Drive

(%)

if Brush-Mode

is active

––––––

all LEDs

flash 6 times

@NEUTRAL

RED or RED & GREEN

if Brushless-Mode

is active

––––––

# of flashes equals

active profile (1-5)

if pressed

––––––

within 3 sec. of

all LEDs flashing

––––––

active profile

changed

if not pressed

––––––

within 3 sec. of

all LEDs flashing