Novak Conv. Kit Vehicle Sheet- OFNA Hyper 7 (55-5017D-1) User Manual
Battery box, Spur gear: 46t pinion gear
Hyper 7™ is a registered trademark of OFNA
®
.
ON/OFF
Switch
Novak HV
ESC
Steering Servo
and Mount
Receiver
Antenna
Mount
#55-5017D-1
8/2008
VEHICLE SPECIFIC INSERT
#5017 OFNA HYPER 7 KIT DIAGRAM
figure 14
07209
0501
7
63
#5017
OFNA
®
HYPER7™
Brushless
Conversion
Kit
P5
Qualit y Racing Electronics since 1978
NOVAK ELECTRONICS, INC.
www.teamnovak.com
©2008 Novak Electronics, Inc. • All Rights Reserved •
No part of these instructions may be reproduced without
the written permission of Novak Electronics, Inc.
Battery Box
(LEFT)
Box mounted as far toward
center of car for body
clearance and optimum
weight balance.
Spur Gear: 46T
Pinion Gear
refer to chart
Pinion Gear Recommendations
Two 2S Li-Po Packs
Motor
Mod 1 Pinion Gear
HV4.5
For speed runs only.
Use biggest pinion gear.
HV5.5
10T
Novak #5110
HV6.5
11T
Novak #5100
HV7.5
12T
Novak #5101
Motor operating temperature is the ONLY way to
set vehicle gearing. The motor and ESC should
not exceed 160-170
o
F MAX at end of run.
F/R Differential
Ratio: 3.31
Novak 550-size HV
Brushless Motor
with Cooling
Fan Installed
Motor solder tabs face outside
of the buggy.
- Brushless Speed Control: Crusher Basic Set-Up (original) (55-1833-1 Rev.2) (2 pages)
- Brushless Speed Control: Crusher Basic Set-Up (w/Simple-Tuner) (55-1834-1 Rev.1) (2 pages)
- Brushless Speed Control: Crusher Field Guide (Crawler Mode) --- Simple-Tuner Version ESC (4) (4 pages)
- Brushless Speed Control: Crusher Field Guide (Standard Modes) --- Simple-Tuner Version ESC (1) (4 pages)
- Brushless Speed Control: Crusher Field Guide -- Original Version (55-1833P-1 Rev.2) (4 pages)
- Brushless Speed Control: Crusher Simple-Tuner Profile Cheat Sheet (14) (1 page)
- Brushless Speed Control: Drift Spec Basic Set-Up (55-3074-1 Rev.1) (2 pages)
- Brushless Speed Control: Drift Spec Track Guide (55-3074P-1 Rev.1) (2 pages)
- Brushless Speed Control: Edge 2S (55-1851-1 Rev.2) (2 pages)
- Brushless Speed Control: Edge Programming Guide (55-1851P-1.7 Rev.7) (2 pages)
- Brushless Speed Control: GTB 3 Basic Set-Up (55-1747-1.2) (2 pages)
- Brushless Speed Control: GTB 3 Track Guide (55-1747P-1.1) (4 pages)
- Brushless Speed Control: Impact Basic Set-Up (55-1730-1 Rev.3) (2 pages)
- Brushless Speed Control: Impact Track Guide (55-1730P-1 Rev.2) (2 pages)
- Brushless Speed Control: Pulse V2 Basic Set-Up (55-1756-2 Rev.2) (2 pages)
- Brushless Speed Control: Pulse V2 Track guide (55-1755P-2 Rev.1) (2 pages)
- Brushless Speed Control: Super-Tuner Brain Board Upgrade Track Guide (55-1746P-1 Rev.2) (2 pages)
- Brushless Speed Control: Timbuk2 Basic Set-Up (55-1832-1 Rev.4) (2 pages)
- Brushless Speed Control: Timbuk2 Field Guide (55-1832P-1 Rev.5) (2 pages)
- Brushed Speed Control: Eiger & Eiger Pro Basic Set-Up Guide (55-1835-1 Rev.6) (2 pages)
- Brushed Speed Control: Eiger & Eiger Pro Field Guide-- NEW version ESCs (standard height heat sinks) (55-1835P-1.4) (4 pages)
- Brushed Speed Control: Eiger & Eiger Pro -- V1 (low profile heat sinks) (55-1835-1.2) (2 pages)
- Brushed Speed Control: M2 Dig Basic Set-Up Guide (55-1846-1.3) (2 pages)
- Brushed Speed Control: M2 Dig Basic Set-Up Guide- 4 Profile Model (55-1846-1.4) (2 pages)
- Brushed Speed Control: M2 Dig Field Guide (55-1846P-1 Rev. 1.1) (4 pages)
- Brushed Speed Control: M2 Dig Field Guide- 4 Profile Model (55-1846P-1 Rev. 1.2) (4 pages)
- Brushless Motor: 4PHD Heavy-Duty 4-Pole BL Motor (55-3510M-1 Rev.1) (2 pages)
- Brushless Motor: 55-5980-1.C__Manufacturing 3-Up Layout (2 pages)
- Brushless Motor: 55-5984-1.D__Manufacturing 6-Up Layout (55-5984-1.D) (2 pages)
- Brushless Motor: 55-6801-1.D__Manufacturing 6-Up Layout (55-6801-1.D) (2 pages)
- Brushless Motor: Ballistic 540/550 Motor (2 pages)
- Brushless Motor: Brushless Motor Rotor and End Bell/Bearing Replacement (2 pages)
- Brushless Motor: Brushless Motor Stator Replacement (55-6801-1.D) (1 page)
- Brushless Motor: Brushless Motor Timing/Sensor Assembly Replacement (55-5984-1.D) (1 page)
- Brushless Motor: Brushless Sensor Harness Removal & Replacement (55-535X-1) (1 page)
- Brushless Motor: Drift Spec Motor (55-3074M-1 Rev.1) (2 pages)
- Brushless Motor: Vulcan Motor (55-3640-1 Rev.3) (2 pages)
- Brushed Motor: Rock Star Motor (55-3557-1 Rev.C) (2 pages)
- Brushed Motor: Terra Claw Motor (55-3556-1 Rev.C) (2 pages)
- 1S LiPo Booster Module (1 page)
- 4PHD Motor Replacement Part (55-5956-1) (2 pages)
- 5463 3A High-Voltage BEC (55-5463-7) (2 pages)
- 55-5750-1.2_Manufacturing 9-Up Layout (55-5750-1.2) (1 page)
- 55-583X-1.2_Manufacturing 6-Up Layout (55-583X-1.2) (1 page)
- 55-5860-1.2_Manufacturing 9-Up Layout (55-5860-1.2) (1 page)