Novak 5463 3A High-Voltage BEC (55-5463-7) - Manual (Page 2)

remove
&
insulate
red
wire
black wire to battery negative red wire to battery positive
power
output lead
4. For Electric Vehicle Installations, remove the RED wire
from the speed control’s input signal harness. Insulate the
removed wire to avoid short circuits, as this wire is “live”.
BEC OPERATION:
1. With a fully-charged battery pack connected to ESC, slide the
ESC’s power switch to ON position (powers up ESC’s electronics) .
2. Slide BEC’s power switch to ON position (BEC powers servo/receiver) .
TROUBLESHOOTING: If there is no power, check the following:
• Check power wire connections from battery to ESC and BEC unit.
• Check that BEC output harness is properly connected to receiver.
• Check that both BEC and speed control are switched ON.
PRODUCT WARRANTY:
Novak R/C, Inc. guarantees all products to be free
from defects in materials or workmanship for a period of 120 days from original date
of purchase (verified by dated, itemized sales receipt). In no case shall our liability
exceed the products original cost. Warranty does not cover water damage, use with
incorrect number of cells, incorrect installation, short-circuiting, failure of main battery
pack, or any damage to other electronics used in conjunction with BEC, including
damage caused by a crash, flooding, or natural disaster. No liability may be assumed
nor will be accepted for any damage resulting from the use of this product. In no case
shall our liability exceed the product’s original cost. We reserve the right to modify
warranty provisions without notice. ©2014 Novak R/C, Inc. All Rights Reserved
www.teamnovak.com
(949) 916-6044 • [email protected] • Mon-Thu
remove
&
insulate
red
wire
black wire to battery negative red wire to battery positive
power
output lead
4. For Electric Vehicle Installations, remove the RED wire
from the speed control’s input signal harness. Insulate the
removed wire to avoid short circuits, as this wire is “live”.
BEC OPERATION:
1. With a fully-charged battery pack connected to ESC, slide the
ESC’s power switch to ON position (powers up ESC’s electronics) .
2. Slide BEC’s power switch to ON position (BEC powers servo/receiver) .
TROUBLESHOOTING: If there is no power, check the following:
• Check power wire connections from battery to ESC and BEC unit.
• Check that BEC output harness is properly connected to receiver.
• Check that both BEC and speed control are switched ON.
PRODUCT WARRANTY:
Novak R/C, Inc. guarantees all products to be free
from defects in materials or workmanship for a period of 120 days from original date
of purchase (verified by dated, itemized sales receipt). In no case shall our liability
exceed the products original cost. Warranty does not cover water damage, use with
incorrect number of cells, incorrect installation, short-circuiting, failure of main battery
pack, or any damage to other electronics used in conjunction with BEC, including
damage caused by a crash, flooding, or natural disaster. No liability may be assumed
nor will be accepted for any damage resulting from the use of this product. In no case
shall our liability exceed the product’s original cost. We reserve the right to modify
warranty provisions without notice. ©2014 Novak R/C, Inc. All Rights Reserved
www.teamnovak.com
(949) 916-6044 • [email protected] • Mon-Thu
remove
&
insulate
red
wire
black wire to battery negative red wire to battery positive
power
output lead
4. For Electric Vehicle Installations, remove the RED wire
from the speed control’s input signal harness. Insulate the
removed wire to avoid short circuits, as this wire is “live”.
BEC OPERATION:
1. With a fully-charged battery pack connected to ESC, slide the
ESC’s power switch to ON position (powers up ESC’s electronics) .
2. Slide BEC’s power switch to ON position (BEC powers servo/receiver) .
TROUBLESHOOTING: If there is no power, check the following:
• Check power wire connections from battery to ESC and BEC unit.
• Check that BEC output harness is properly connected to receiver.
• Check that both BEC and speed control are switched ON.
PRODUCT WARRANTY:
Novak R/C, Inc. guarantees all products to be free
from defects in materials or workmanship for a period of 120 days from original date
of purchase (verified by dated, itemized sales receipt). In no case shall our liability
exceed the products original cost. Warranty does not cover water damage, use with
incorrect number of cells, incorrect installation, short-circuiting, failure of main battery
pack, or any damage to other electronics used in conjunction with BEC, including
damage caused by a crash, flooding, or natural disaster. No liability may be assumed
nor will be accepted for any damage resulting from the use of this product. In no case
shall our liability exceed the product’s original cost. We reserve the right to modify
warranty provisions without notice. ©2014 Novak R/C, Inc. All Rights Reserved
www.teamnovak.com
(949) 916-6044 • [email protected] • Mon-Thu
remove
&
insulate
red
wire
black wire to battery negative red wire to battery positive
power
output lead
4. For Electric Vehicle Installations, remove the RED wire
from the speed control’s input signal harness. Insulate the
removed wire to avoid short circuits, as this wire is “live”.
BEC OPERATION:
1. With a fully-charged battery pack connected to ESC, slide the
ESC’s power switch to ON position (powers up ESC’s electronics) .
2. Slide BEC’s power switch to ON position (BEC powers servo/receiver) .
TROUBLESHOOTING: If there is no power, check the following:
• Check power wire connections from battery to ESC and BEC unit.
• Check that BEC output harness is properly connected to receiver.
• Check that both BEC and speed control are switched ON.
PRODUCT WARRANTY:
Novak R/C, Inc. guarantees all products to be free
from defects in materials or workmanship for a period of 120 days from original date
of purchase (verified by dated, itemized sales receipt). In no case shall our liability
exceed the products original cost. Warranty does not cover water damage, use with
incorrect number of cells, incorrect installation, short-circuiting, failure of main battery
pack, or any damage to other electronics used in conjunction with BEC, including
damage caused by a crash, flooding, or natural disaster. No liability may be assumed
nor will be accepted for any damage resulting from the use of this product. In no case
shall our liability exceed the product’s original cost. We reserve the right to modify
warranty provisions without notice. ©2014 Novak R/C, Inc. All Rights Reserved
www.teamnovak.com
(949) 916-6044 • [email protected] • Mon-Thu
remove
&
insulate
red
wire
black wire to battery negative red wire to battery positive
power
output lead
4. For Electric Vehicle Installations, remove the RED wire
from the speed control’s input signal harness. Insulate the
removed wire to avoid short circuits, as this wire is “live”.
BEC OPERATION:
1. With a fully-charged battery pack connected to ESC, slide the
ESC’s power switch to ON position (powers up ESC’s electronics) .
2. Slide BEC’s power switch to ON position (BEC powers servo/receiver) .
TROUBLESHOOTING: If there is no power, check the following:
• Check power wire connections from battery to ESC and BEC unit.
• Check that BEC output harness is properly connected to receiver.
• Check that both BEC and speed control are switched ON.
PRODUCT WARRANTY:
Novak R/C, Inc. guarantees all products to be free
from defects in materials or workmanship for a period of 120 days from original date
of purchase (verified by dated, itemized sales receipt). In no case shall our liability
exceed the products original cost. Warranty does not cover water damage, use with
incorrect number of cells, incorrect installation, short-circuiting, failure of main battery
pack, or any damage to other electronics used in conjunction with BEC, including
damage caused by a crash, flooding, or natural disaster. No liability may be assumed
nor will be accepted for any damage resulting from the use of this product. In no case
shall our liability exceed the product’s original cost. We reserve the right to modify
warranty provisions without notice. ©2014 Novak R/C, Inc. All Rights Reserved
www.teamnovak.com
(949) 916-6044 • [email protected] • Mon-Thu
remove
&
insulate
red
wire
black wire to battery negative red wire to battery positive
power
output lead
4. For Electric Vehicle Installations, remove the RED wire
from the speed control’s input signal harness. Insulate the
removed wire to avoid short circuits, as this wire is “live”.
BEC OPERATION:
1. With a fully-charged battery pack connected to ESC, slide the
ESC’s power switch to ON position (powers up ESC’s electronics) .
2. Slide BEC’s power switch to ON position (BEC powers servo/receiver) .
TROUBLESHOOTING: If there is no power, check the following:
• Check power wire connections from battery to ESC and BEC unit.
• Check that BEC output harness is properly connected to receiver.
• Check that both BEC and speed control are switched ON.
PRODUCT WARRANTY:
Novak R/C, Inc. guarantees all products to be free
from defects in materials or workmanship for a period of 120 days from original date
of purchase (verified by dated, itemized sales receipt). In no case shall our liability
exceed the products original cost. Warranty does not cover water damage, use with
incorrect number of cells, incorrect installation, short-circuiting, failure of main battery
pack, or any damage to other electronics used in conjunction with BEC, including
damage caused by a crash, flooding, or natural disaster. No liability may be assumed
nor will be accepted for any damage resulting from the use of this product. In no case
shall our liability exceed the product’s original cost. We reserve the right to modify
warranty provisions without notice. ©2014 Novak R/C, Inc. All Rights Reserved
www.teamnovak.com
(949) 916-6044 • [email protected] • Mon-Thu