Philips VHS VR6393 - Manual (Page 16)

• Press the coloured button on the remote control which
corresponds to the colour of what you want to change on the TV
screen.
• Use + or — or the digit buttons (0-9), to change the data.
Note:
If you use the digit buttons (0-9), the date and the preselection
number have to be entered in a two-digit form, e.g. ‘01 ’ for
preselection number 1.
• Press (?) on the remote control to get additional help
information on the screen.
VPS
VPS control will select automatically the correct VPS-time.
If you want to make a timed recording from a TV station without
VPS-code, or if you want to use a starttime which is different
from the VPS-starttime, VPS must be switched off.
If you want to switch off the VPS control for this TIMER-block:
• Press the blue button on the remote control.
‘PROG’ will flash on the TV screen.
• Press X on the remote control - VPS will disappear from the
screen.
If you want to switch on the VPS control again:
• Press X again VPS will appear on the screen.
If real start time and VPS-time are different, the starttime is
corrected automatically, when VPS control is set.
Note:
If ‘TEXT-PROGRAMMING’ has been indicated during selection
of the desired programme VPS-control may not be selected
automatically:
— If VPS-control is required, you may select it.
In this case, be sure that the start time is corrected to the
advertised VPS-time.
— The recording date, the end-time and the preselection
number have to be checked and changed if required.
(D
Press
(®^).
The TV screen shows a summary of all programmed
TlMER-blocks.
Note:
You can recall this TIMER summary at any time (except
record), also if TXT is not selected by pressing OSD button
(Q).
To switch off the TIMER summary, press (C3) again.
® If you want to continue programming a new block, start from
step ©.
•
If you want to interrupt programming, press TXT button (ID).
• If you want to return to live TV-picture, press (ID) again.
General notes:
— During TXT, playback and wind functions are Impossible.
— If you press (D) during programming with TXT, the
videorecorder will be switched to TXT-mode without changing
any data.
— During the first VPT-programming procedure, the video
recorder requests to check the preselection number to be
recorded.
Following example illustrates how the automatic ‘TV station
recognition’ works:
• Preselection number ‘1 ’ is stored for ‘ZDF’
• Preselection number ‘2’ is stored for ‘ARD’
•
Preselection number ‘3’ is stored for ‘BR’
• All these 3 TV stations have the same TXT-system and each
TV station shows all 3 program summaries,
• Preselection number ‘1/ZDF’ Is selected on the VCR.
• You want to program a timed recordidng from ‘2/ARD' by
VPT-programming.
Choose the desired TV programme - the VCR asks to check
the preselection number.
• Select ‘2’ for ‘ARD’ and press (® <$•) to confirm the
preselection number.
Finalize the programming sequence following steps (a) and
The preselection number ‘2’ is now assigned to the TV station
‘ARD’.
• Anytime a recording from ‘ARD’ is wanted again, the video
recorder does the selection of the preselection number ‘2’
automatically.
The same assigments are possible for all other preselection
numbers.
• If a wrong preselection number for a TV station was entered,
it can be corrected at the next programming procedure by
pressing the blue button fl—i) and correcting the preselection
number.
• These assignments are stored in the VCR unit mains power
is interrupted.
Programming a timed recording on the video recorder (without
TXT)
TXT subtitle recording
© Press ®(® <$*).
The Display shows, for example:
T I IT/CO
I I ) i/_i'
All necessary information for recordings are stored in TIMER
blocks.
Each TIMER block contains a start time, a stop time, a date and
a preselection number of a TV programme.
There are 6 TIMER blocks available, so you can program the
video recorder to record 6 TV programmes successively.
Note:
If all the TIMER blocks are programmed, the Display shows
‘FULL’, and then after a few seconds:
@ If necessary, press + or — or the digit buttons (0-9) on the
remote control to select the block you want to program.
Note:
To record TXT-subtitles use TIMER-block 6.
12 (gg)