Interlogix NX-8V2 REV B Installation Manual - Manual (Page 3)

Select the module to program
Since all modules connected to the NX-8V2 are programmed
through the keypad, the module you are programming should
be the first entry. To select the module to program, enter 0, #.
The 0 is the module number of the control, and # is the entry
key. You can find other module entry numbers in the module
documentation.
Program a location
Once you enter the module number, the Armed LED
illuminates, indicating the keypad is waiting for you to enter a
programming location. To program a location, do the following:
1. To access any location, enter the desired programming
location, followed by #. If the location is a valid location,
the Armed LED extinguishes, the Ready LED illuminates,
and the binary data for the first segment of the location is
shown by the Zone LEDs.
2. While entering new data, the Ready LED begins flashing
to indicate a data change in process.
3. Press
 to store the newly entered data. The keypad
advances to the next segment and displays its data.
Repeat this procedure until the last segment is reached.
4. To move to another location after exiting a location (Armed
LED illuminated):
• Press the Police key for the next sequential location.
• Press the Fire key for the previous location.
• Press the Medical key for the same location.
5. To review the data in a specific location, repeat the above
procedure, pressing
 but with no numeric data entry.
Each time you press
, the programming data of the next
segment displays.
Exit a location
To exit the current programming location, do the following:
1. Press the
 key. The Ready LED goes off and the Armed
LED goes on. You must press the
key to save the data.
2. To exit before the last segment, press # (Armed LED
illuminates).
You are now ready to enter another programming location. If
you attempt to program an invalid entry for a particular
segment, the keypad beeps three times indicating an error and
remains in that segment awaiting a valid entry.
Exit program mode
To exit program mode, do the following:
1. When you have completed all programming, press Exit to
leave the selected module.
2. If there is another module to be programmed, select it by
entering its address, followed by #. The procedure for
programming these devices is the same as for the control
panel, except the locations are for the module selected.
3. If no additional modules are to be programmed, press Exit
again to leave program mode.
Loading factory defaults
To load factory defaults, enter program mode, enter the device
address and number and then enter 9, 1, 0, #. The keypad
beeps three times indicating that loading is in progress. The
process takes about six seconds. You cannot exit the location
until loading is completed.
Enrolling modules and keypads
The NX-8V2 automatically finds and stores all keypads, zone
expanders, wireless receivers, and other modules connected
to the data terminal into the NX-8V2 memory. This allows the
modules to be supervised by the control panel.
To enroll the modules, do the following:
1. Enter program mode and program the desired settings for
each module.
2. When you exit program mode, the NX-8V2 automatically
enrolls the devices. The enrolling process takes about 12
seconds, during which time the Service LED illuminates. If
a speaker is attached to the NX-8V2, it clicks at this time.
If a siren or bell is attached to the NX-8V2, it sounds for
about one second. If the module is not detected, the
Service LED illuminates.
Note: User codes are not accepted during the enrolling
process.
Quick start programming locations
For most routine installations, the quick start locations allow
you to enable a majority of the options available with the NX-
8V2 (when communicating in Contact ID or SIA formats). The
quick start locations include:
• Location 0 - Phone 1
• Location 1 - Phone 1 account code
• Location 2 - Phone 1 communicator format
• Location 3 - Phone 1 dial attempts/backup control
NX-8V2 Control Panel Installation Instructions 3