Interlogix NX-4V2 Installation Guide - Manual (Page 5)

• Program a 1 in segment 2 to cause the NX-4V2 to stop
ake
, the next two attempts to
Location 4 has two segments of feature selection data. Use
to select those events reported to phone 1.
plit reporting, use Location 4 to
one 1.
eporting and the split is based on
ported to phone 1.
ne 1, program 0 in
and alarm restores.
losings.
and trouble restores.
ow battery
mplete.
nd tamper restore.
wer overcurrent, ground fault, and restore for
8 - Custom communicator format
ection data. Use
at used to
your
which
4. If
you need a format other than those listed, review the override
bed in this location to build the appropriate
Hz.
0 Hz handshake; off for 1400 Hz.
for one-digit event code.
s; off for 20 or 40 pps.
rmat (no handshake required).
3. Reserved.
Location 25 - Zones 1 to 8 zone type
ht segments of numerical data. Use this
prog type for zones 1 to 8. Use
or z ent
defaults are 3, 5
prog
17 t
ean
Table 5 on pag the zone types.
trying to communicate after the designated number of
attempts have been made to phone 1.
• Program a 2 in segment 2 to cause the NX-4V2 to m
the dial attempts in increments of two. The first two
attempts are made to phone 1
phone 2. This repeats until the total number of attempts
designated in segment 1 is completed.
Location 4 - Phone 1 events reported
this location
• If you do not want dual or s
select all events to ph
• If you want dual or split r
the event type (alarm, open/close, etc.), use Location 4 to
select only those events that are re
• If you don’t want events reported to pho
Location 4 (disabling all options).
Segment 1
1. Alarms
2. Opening and c
3. Zone bypass and bypass restores.
4. Zone trouble
5. Power fail, low battery, power restore, and l
restore.
6. Bell cut, telephone line cut, bell cut restore, telephone line
restore.
7. Test reports.
8. Start and end programming, download co
Segment 2
1. Zone and box tamper a
2. Auxiliary po
both.
3. Wireless sensor missing and restore.
4. Wireless sensor low battery and restore.
5. Expander trouble and restore.
6. Fail to communicate.
7. Zone activity monitor.
8. Reserved
Location 1
Location 18 has four segments of feature sel
this location to program the communicator form
transmit to the receiver connected to phone 3. Refer to
central station receiver documentation to determine
format is compatible. Select a format from Table 4 on page
options descri
format.
Segment 1
1. On for 1800 Hz transmit; off for 1900
2. On for 230
3. On for cksum parity; off for double round parity.
4. On for two-digit event code; off
5. Reserved.
6. Reserved.
7. On for 20 pps; off for 10 or 40 pps.
8. On for 10 pp
Segment 2
1. On for pager fo
2. On for 1400/2300 handshake.
4. Reserved.
5. On for contact ID.
6. On for SIA.
7. On for contact ID or 4+3.
8. On for DTMF.
Segments 3 and 4 - Reserved
Location 25 has eig
location to ram the zone
segment 1 f one 1, segment 2 for zone 2, etc. The segm
, 6, 6, 6, 6, 6, 6.
Zones are
zone types
rammed to be one of thirty different types. Use
hrough 20 for wireless, or for hardwired zones
using Europ double EOL configuration
e 6 describes
NX-4V2 Control Panel Installation Instructions 5