Interlogix NX-4V2 Installation Guide - Manual (Page 3)

key. You can find other module entry numbers in the module
illum
prog
1.
location is a valid location,
nt of the location is
2. ing
xt segment and displays its data.
cation (Armed
•
•
5. n a specific location, repeat the above
procedure, pressing
 but with no numeric data entry.
press
, the programming data of the next
exit the current progr
1. y. The Ready LED goes off and the Armed
D
g location. If
you attempt to program an invalid entry for a particular
eps three times indicating an error and
entry.
exit progra
1. to
2.
s is the same as for the control
xit
ts
de, enter the device
1, 0, #. The keypad
expa receivers, and other modules connected
To e
1.
2. ode, the NX-4V2 automatically
If
is attached to the NX-4V2, it clicks at this time.
unds for
, the
u ming locations
r ns allow
u X-
). The
quick start locations include:
Location 3 - Phone 1 dial attempts/backup control
Loc
ca
.
ds, enter 13 in the
appropriate segment.
documentation.
Program a location
Once you enter the module number, the Armed LED
inates, indicating the keypad is waiting for you to enter a
ramming location. To program a location, do the following:
To access any location, enter the desired programming
location, followed by #. If the
the Armed LED extinguishes, the Ready LED illuminates,
and the binary data for the first segme
shown by the Zone LEDs.
While entering new data, the Ready LED begins flash
to indicate a data change in process.
3. Press
 to store the newly entered data. The keypad
advances to the ne
Repeat this procedure until the last segment is reached.
4. To move to another location after exiting a lo
LED illuminated):
• Press the Police key for the next sequential location.
Press the Fire key for the previous location.
Press the Medical key for the same location.
To review the data i
Each time you
segment displays.
Exit a location
To amming location, do the following:
Press the
 ke
LED goes on. You must press the
key to save the data.
2. To exit before the last segment, press # (Armed LE
illuminates).
You are now ready to enter another programmin
segment, the keypad be
remains in that segment awaiting a valid
Exit program mode
To m mode, do the following:
When you have completed all programming, press Exit
leave the selected module.
If there is another module to be programmed, select it by
entering its address, followed by #. The procedure for
programming these device
panel, except the locations are for the module selected.
3. If no additional modules are to be programmed, press E
again to leave program mode.
Loading factory defaul
To load factory defaults, enter program mo
address and number and then enter 9,
beeps three times indicating that loading is in progress. The
process takes about six seconds. You cannot exit the location
until loading is completed.
Enrolling modules and keypads
The NX-4V2 automatically finds and stores all keypads, zone
nders, wireless
to the data terminal into the NX-4V2 memory. This allows the
modules to be supervised by the control panel.
nroll the modules, do the following:
Enter program mode and program the desired settings for
each module.
When you exit program m
enrolls the devices. The enrolling process takes about 12
seconds, during which time the Service LED illuminates.
a speaker
If a siren or bell is attached to the NX-4V2, it so
about one second. If the module is not detected
Service LED illuminates.
Note : User codes are not accepted during the enrolling
process.
Q ick start program
Fo most routine installations, the quick start locatio
yo to enable a majority of the options available with the N
4V2 (when communicating in Contact ID or SIA formats
• Location 0 - Phone 1
• Location 1 - Phone 1 account code
• Location 2 - Phone 1 communicator format
•
ation 0 - Phone 1
Location 0 has 20 segments of numerical data. Use this
tion to program phone 1. T lo he default for each segment is
14
• To program a delay of four secon
NX-4V2 Control Panel Installation Instructions 3