Interlogix NX-4V2 Installation Guide - Manual (Page 2)

Terminal Description
SMOKE+ Smoke detector power 12 V, 1.5 A maximum.
AUX2
t
t is negative, and 250 µA when output is
Connect negative lead of low current device [relay, LED
(install 1 Kohm
resistor in series with LED), etc.]. Connec
positive lead of device to COM. Current is limited to 50
mA when outpu
positive.
DATA
ximum number of devices: 8 keypads + 1
Connect to the data terminal on the keypads and the
expanders. Ma
other device.
COM ommon terminal on the keypads and the Connect to the c
expanders.
POS Connect to the POS terminal on the keypads and the
expanders. Individually, this terminal is limited to 1 A.
ZONE4
n wire or a short in the
Connect to one side of the zone 4 loop. Connect the other
side to the COM terminal. An ope
wire will cause alarm.
COM Common (-) terminal for zones 3 and 4.
ZONE3
inal. An open wire or a short in the wire
Connect to one side of the zone 3 loop. Connect the other
side to COM term
will cause alarm.
ZONES
1-2
inal. An open wire or a short in the wire
will cause alarm.
Connect to one side of the zone loop. Connect the other
side to COM term
Module list
Table 3 below shows the modules that are compatible with the
NX-4V2 system. Additional information and a catalog listing all
system components is available from Customer Support
o n be added to the NX-4V2 Table 3: M dules that ca
Terminal Description
NX-108E 8-zone LED keypad
NX-116E 16-zone LED keypad
NX-124E 24-zone LED keypad
NX-148E Alphanumeric 48-zone LCD keypad
NX-148E-
RF
b
Alphanumeric 48-zone LCD keypad with built-in 48-zone
wireless receiver
NX-200 a 4k and one Zone doubling kit (includes one hundred 3.7
hundred 6.98k resistors)
NX-320E Smart power supply and bus extender
NX-408E wireless expansion module (UL listed part #60- 8-zone
904)
NX-416E wireless expansion module (UL listed part #60- 16-zone
904)
NX-448E wireless expansion module (UL listed part #60- 48-zone
904)
NX-508E Eight-output module
NX-534E Two-way listen-in module
Terminal Description
NX-540E
a
Operator telephone interface module
NX-548E b 48-zone wireless receiver
NX-5
GSM
a
91E- Cell interface
NX-
1192E 192-zone LCD keypad
NX-
1208E 8-zone LED keypad
NX-
1248E 48-zone LCD keypad
NX-
1308E 8-zone LED door design keypad
NX-
1316E 16-zone LED door design keypad
NX-
1324E 24-zone LED door design keypad
NX-
1448E 48-zone fixed language icon keypad
a> These products have not been tested and approved by
Underwriters Laboratories, In.
b> These wireless devices are UL listed only for residential
applications.
Note: The NX-4V2 control panel sends a trouble condition
ave been enrolled.
ce zero (0).
u to enter program
mode, select the module to program, program a location, and
rogram mode.
2. e
s,
and the five function LEDs illuminate. You are now in
e module to program.
ule number of the control, and # is the entry
once each hour if it senses that no devices h
This report shows expander trouble--devi
Control panel programming
Programming the control panel requires yo
then exit the location and p
Enter program mode
T
o enter program mode, do the following:
1. Press
8. The five function LEDs (Stay, Chime, Exit,
Bypass, and Cancel) begin flashing.
Enter the go to program code (default is 9, 7, 1, 3). If th
go to program code entry is valid, the Service LED flashe
program mode and can select th
Select the module to program
Since all modules connected to the NX-4V2 are programmed
through the keypad, the module you are programming should
be the first entry. To select the module to program, enter 0, #.
The 0 is the mod
2 NX-4V2 Control Panel Installation Instructions