Great Planes Escapade EP/GP ARF - GPMA1200 - Manual (Page 4)

4
❏
(1) Great Planes ElectriFly Equinox 4S/5S 4S adapter
set for each Equinox balancer (GPMM3162)
❏
8mm prop reamer (for propellers and included spinner
– GPMQ5007)
❏
Great Planes Pro ™ 30-minute epoxy (GPMR6043) (for
gluing motor mount to fuselage)
IMPORTANT: The Escapade requires a single, 4S battery
pack. But if experimenting with different battery combinations
and connecting multiple battery packs with adapter plugs,
refer to the Battery Precautions on page 20.
Glow Engine Recommendations
The recommended glow engine size range for the Escapade
is printed on the cover of this instruction manual. It will fl y
well with any of the engines within the recommended range.
And, the Escapade is a lightweight model, so when fl own
with engines even at the smaller end of the scale it will still be
fast and responsive. So, unless you are an experienced pilot,
you may be better off starting out with a smaller engine.
In addition to the engine, following are the additional items
required if powering your Escapade with a glow engine:
❏
Suitable propeller and spare propellers
❏
Fuel, fueling system (pump, fuel line, fuel can fi ttings
set), 1.5V glow driver, fi eld box, tools
❏
#36 (or 7/64) [2.6mm] drill
❏
Optional: 6-32 tap and drill set (GPMR8102), (4) 6-32
x 1" socket-head cap screws (GPMQ3038) for mounting
engine with machine screws instead of included sheet-
metal screws.
Radio Equipment
4-channels are required to fl y the Escapade. However, the
number of servos required can be from three to fi ve. Only
three channels will be required if fl ying the Escapade with
an electric motor and using the single aileron servo option.
If powering the model with a glow engine, a servo will be
required for the throttle. And in either case (glow or electric),
two servos will be required for the ailerons if using the dual
aileron servo option. In all cases, standard-size servos with
standard output torque (40 – 50 oz-in torque) are suitable.
Following is the specifi c radio gear required for the
different confi gurations:
For all versions;
❏
4-channel radio system w/4.8V 500-600mAh fl at Rx
battery back, on/off switch
❏
1 ea. standard size/torque elevator and rudder servo
For single aileron servo option:
❏
(1) standard torque/size aileron servo
❏
(2) 6" [150mm] servo extension wires (HCAM2000)
For dual aileron servo option:
❏
(2) standard torque/size aileron servos
❏
(2) 6" [150mm] servo extension wires (HCAM2000
for Futaba ® )
❏
(1) Dual servo extension (FUTM4130 for Futaba)
ADDITIONAL ITEMS REQUIRED
In addition to common hobby tools (screwdrivers, pliers, wire
cutters), following is a list of suggested building supplies:
❏
1/2 oz. [15g] Medium Pro ™ CA+ (GPMR6007)
❏
1/2 oz. [15g] Thin Pro CA (GPMR6001)
❏
CA applicator tips (HCAR3780)
❏
#1 Hobby knife (HCAR0105)
❏
#11 Blades (5-pack, HCAR0211)
❏
Power drill
❏
Drill bits; 1/16" [1.6mm], 3/32" [2.4mm], #48 (.076" [1.9mm])
drill or hobby knife
❏
Great Planes Pro Threadlocker (GPMR6060)
❏
21st Century ® sealing iron (COVR2700)
Optional Supplies & Tools
Here is a list of optional tools mentioned in the manual that
will help you build the Escapade.
❏
21st Century iron cover (COVR2702)
❏
21st Century trim seal iron (COVR2750)
❏
Stick-on segmented lead weights (GPMQ4485)
❏
2 oz. [57g] Spray CA activator (GPMR6035)
❏
Dead Center ™ Engine Mount Hole Locator (GPMR8130)
❏
C.G. Machine ™ (GPMR2400)
❏
Precision Magnetic Prop Balancer ™ (TOPQ5700)
IMPORTANT BUILDING NOTES
• There are two types of screws used in this kit:
• Sheet Metal Screws are designated by a number and
a length. For example #6 x 3/4" [19mm].
This is a number six screw that is 3/4" [19mm] long.
• Machine screws are designated by a number, threads
per inch, and a length. For example 4-40 x 3/4" [19mm]
This is a number 4 screw that is 3/4" [19mm] long
with forty threads per inch.
• The Escapade is factory-covered with Top Flite ®
MonoKote ® fi lm. Should repairs ever be required,
MonoKote can be patched with additional MonoKote