Estes 2110 - Outlander - Manual

ESTES INDUSTRIES
1295 H Street
Penrose, CO 81240
EST 2110
SHOCK CORD (1/4" x 24")
(38383)
FLYING MODEL ROCKET KIT INSTRUCTIONS
www.estesrockets.com
KEEP FOR FUTURE REFERENCE
ASSEMBLY TIP: Read all instructions
before beginning work on your model. Make
sure you have all parts and supplies.
TEST FIT ALL PARTS TOGETHER
BEFORE APPLYING ANY GLUE!
If any parts don't fit properly, sand as
required for precision assembly.
PARTS
Locate the parts shown below and lay them out on the table in front of
you. DO NOT USE THIS DRAWING TO ASSSEMBLE YOUR ROCKET.
SUPPLIES In addition to the parts included in the kit you will also need:
HELPFUL HINT: IF NOSE CONE/COUPLER FIT IS. . .
TOO
TIGHT TOO
LOOSE
ADD
MASKING TAPE.
SAND FOR FIT.
DIE-CUT BALSA SHEET
(32214)
DIE-CUT BALSA SHEET
(32215)
DECAL SHEET (60550)
DIE-CUT CARD
(32435)
DIE-CUT CARD
(32436)
ENGINE HOOK
(35021)
ELASTIC CORD
(38224)
SILICONE HINGE TUBE (1/8" x 4")
(60544)
ASSEMBLED
PARACHUTE
18" (45 cm)
(35802)
WOODEN DOWEL 1/12 x 2
(32058)
YELLOW FOOT PAD RING (4)
EB-20B (30171-4)
GREEN CENTERING RING
AR-2050 (30164-2)
PLASTIC HINGE
BALL STRAND
(60543)
WOODEN DOWEL (1/8" x 9") (8)
(32054)
LARGE TANK
BT-50 (3") (4)
(30412)
SMALL TANK
BT-20 (1 1/2") (8)
(30319)
LAUNCH LUG (9 1/16")
(38185)
LAUNCH LUG (1/4") (4)
(38176)
ENGINE MOUNT
TUBE BT-20 (5")
(30310)
UPPER BODY TUBE
BT-60 (5 11/16")
(30402)
LOWER BODY
TUBE BT-60 (2")
(30411)
SCISSORS PENCIL RULER FINE
SANDPAPER
(#400-600 GRIT)
CARPENTER'S
GLUE
MODELING
KNIFE
PLASTIC
CEMENT MASKING
TAPE
SPRAY
PRIMER
WHITE
SPRAY PAINT:
BLUE, RED,
SILVER, BLACK
RAZOR
SAW
SPRAY
CLEAR
COAT
PAINT
PEN
ASCENT MODULE/
NOSE CONE
(60542)
12
ROUND
FILE
© 2003 Estes-Cox Corp. All rights reserved.
FLYING YOUR ROCKET
Choose a large field (500 ft. [152 m] square) free of dry weeds and
brown grass. The larger the launch area, the better the chance of
recovering your rocket. Football fields and playgrounds are great.
Launch only with little or no wind and good visibility.
Always follow the National Association of Rocketry (NAR)
Safety Code.
MISFIRES
TAKE THE KEY OUT OF THE CONTROLLER. WAIT ONE MINUTE
BEFORE GOING NEAR THE ROCKET! Disconnect the igniter clips and
remove the engine. Take the plug and igniter out of the engine. If the igniter
has burned, it worked but did not ignite the engine because it was not
touching the propellant inside the engine. Put a new igniter all the way
inside the engine without bending it. Push the plug in place. Repeat the
steps under Countdown and Launch.
NAR Safety Code
NO DRY GRASS
OR WEEDS
PRECAUTIONS
LAUNCH SUPPLIES (Sold Separately)
• Porta Pad® II Launch Pad
• Electron Beam® Launch Controller
• Recovery Wadding
• Igniters (with Engines)
• Igniter Plugs (with Engines)
• Recommended Estes® Engines:
B4-2, B6-2, C6-3
KEY ALWAYS OUT UNTIL
FINAL COUNTDOWN!
COUNTDOWN AND LAUNCH
2... 2...
HOLD KEY DOWN AND
PRESS LAUNCH BUTTON
UNTIL LIFT-OFF!
1... 1...
4... 4...
INSERT KEY.
PUSH DOWN
AND HOLD.
LAUNCH
BUTTON
8" (20 cm)
Masking
Tape
4...
3... 2...
1...
P/N 60545 (9-03)
3... 3...
PRINTED IN CHINA
KEY
5... 5...
15 FT. (5 M)
SLIDE ROCKET
DOWN OVER
LAUNCH ROD.