Estes 1972 – Bullpup 12D - Manual

ESTES INDUSTRIES
1295 H Street
Penrose, CO 81240
1972
FLYING MODEL ROCKET KIT INSTRUCTIONS
www.estesrockets.com
KEEP FOR FUTURE REFERENCE
ASSEMBLY TIP: Read all
instructions before beginning
work on your model. Make sure
you have all parts and supplies.
TEST FIT ALL PARTS
TOGETHER BEFORE
APPLYING ANY GLUE!
If any parts don't fit properly,
sand as required for precision
assembly.
PARTS Locate the parts shown below and lay them out on the table in front
of you. DO NOT USE THIS DRAWING TO ASSEMBLE YOUR ROCKET.
SUPPLIES In addition to the parts included in the kit you will also need:
HELPFUL HINT: IF NOSE CONE/COUPLER FIT IS. . .
TOO
TIGHT TOO
LOOSE
ADD
MASKING TAPE.
SAND FOR FIT.
SCISSORS CARPENTER'S
GLUE
PLASTIC
CEMENT
4
© 2003 Estes-Cox Corp. All rights reserved.
FLYING YOUR ROCKET
Choose a large field (500 ft. [152 m] square) free of dry weeds and brown grass. The
larger the launch area, the better the chance of recovering your rocket. Football fields
and playgrounds are great. Launch only with little or no wind and good visibility.
Always follow the National Association of Rocketry (NAR) Safety Code.
MISFIRES
TAKE THE KEY OUT OF THE CONTROLLER. WAIT ONE MINUTE
BEFORE GOING NEAR THE ROCKET! Disconnect the igniter clips and remove the
engine. Take the plug and igniter out of the engine. If the igniter has burned, it worked
but did not ignite the engine because it was not touching the propellant inside the
engine. Put a new igniter all the way inside the engine without bending it. Push the plug
in place. Repeat the steps under Countdown and Launch.
NAR Safety Code
NO DRY GRASS
OR WEEDS
P/N 83847 (10-03)
PRINTED IN CHINA
ENGINE SPACER
TUBE
(35003)
SHOCK CORD
MOUNT
SECTION
3
SECTION
2
SECTION
1
PENCIL RULER FINE
SANDPAPER
MODELING
KNIFE
MASKING
TAPE
SPRAY
PRIMER
(WHITE)
CLEAR
SPRAY
PRIMER
(OPTIONAL)
HOBBY SAW SPRAY
PAINT
(WHITE)
BULLPUP 12D
HOW TO USE THESE INSTRUCTIONS:
READ ALL INSTRUCTIONS BEFORE STARTING WORK ON THIS MODEL.
A. Read each step first and visualize the
procedure thoroughly in your mind before
starting construction.
B. Lay the parts out on the table in front of
you. (Check inside tubes for any small parts.)
C. Use the parts layout to match all parts
contained in kit.
D. Collect all construction supplies that are
not included in this kit.
E. Sand parts as necessary for proper fit.
F. The construction supplies required for each
step are listed at the beginning of each step.
G. Check off each step as you complete it.
ENGINE BLOCK
(GREEN)
(30162-2)
LAUNCH LUG
(38175)
BODY TUBE
(30384)
ENGINE MOUNT
TUBE
(30324)
TAIL CONE
(30101)
NOSE CONE
(71070)
CENTERING
RINGS
(30125)
SHOCK CORD
(38374)
CLAY WEIGHT (2)
(85705)
ASSEMBLED PARACHUTE
12" (30 CM) (35801)
WRAP LINES LOOSELY AROUND THE
PARACHUTE AND INSERT THE PARACHUTE
INTO THE ROCKET.
COUNTDOWN
AND LAUNCH
LAUNCH SUPPLIES
To launch your rocket, you will need the
following:
• Launch Pad (Estes Porta-Pad
® II)
• Launch Controller (Electron Beam ® )
• Recommended Estes Engines: A8-3 (First
Flight) B4-4, B6-4, B8-5, C6-5
Use an A8-3 engine for your first flight to
become familiar with your rocket's flight
pattern.
• Recovery Wadding (EST 302274)
• Igniters and Igniter Plugs (included with
Estes engines)
Use only Estes products to launch this
rocket.
SEPARATE IGNITER PLUG AND IGNITER.
HOLD ENGINE
UPRIGHT,
DROP IN
IGNITER.
IGNITER MUST
TOUCH
PROPELLANT. INSERT
IGNITER
PLUG. FIRMLY PUSH
ALL THE WAY IN.
FOLD BACK
AND BEND TIPS
AS SHOWN. INSERT ENGINE
INTO ROCKET.
KEY ALWAYS OUT UNTIL
FINAL COUNTDOWN!
HOLD KEY DOWN AND PRESS
LAUNCH BUTTON UNTIL LIFT-OFF!
1 5 F T. (
5 M )
4...
3... 2... 1...
INSERT KEY.
PUSH DOWN
AND HOLD.
8” (20.4 cm)
MASKING
TAPE
ROCKET PREFLIGHT
PREPARE ENGINE
CRUMPLE AND INSERT
3 SQUARES OF
RECOVERY WADDIING
SPIKE FOLD ROLL
NOTE: Parachute
may be dusted with
talcum powder to
avoid sticking.
NOTE: Igniter plugs come with rocket engines. If your
engines did not come with plugs, follow the instructions
that came with the engines.
WRAP WITH 1 OR
2 WRAPS OF
MASKING TAPE
1... 1...
2... 2...
3... 3...
4... 4...
LAUNCH BUTTON
PRECAUTIONS
KEY
NOTE: Use Estes Wadding
(EST 302274) Only.
FINS FINS FINS FINS
LA
UNCH LUG
MA
TCH LINES
MA
TCH LINES
TUBE MARKING
GUIDE
DIE-CUT BALSA
SHEET
(32702)
DECAL
(37289)