5 digital i/o – Digilent EVB-USB3300-XLX User Manual
Page 3
EVB-USB3300-XLX User Manual
SMSC EVB-USB3300-XLX
Revision 0.4 (06-29-07)
3
2.5
Digital I/O
The ULPI signals are routed to connector J1 for connection to the ML401. Each signal on J1 is
described in
Table 2.1
. All ULPI signals are 3.3V CMOS compatible.
Table 2.1 Signals on 3x13-Pin Header
J1 Pin
Signal Name
J1 Pin
Signal Name
J1 Pin
Signal Name
1
+5V
2
GND
3
Reset
4
+5V
5
GND
6
NXT
7
+5V
8
GND
9
CLKOUT
10
+5V
11
GND
12
DIR
13
NC
14
GND
15
STP
16
+3.3V
17
GND
18
DATA7
19
+3.3V
20
GND
21
DATA6
22
+3.3V
23
GND
24
DATA5
25
+3.3V
26
GND
27
DATA4
28
NC
29
GND
30
DATA3
31
RSVD1
32
GND
33
DATA2
34
RSVD2
35
GND
36
DATA1
37
RSVD3
38
GND
39
DATA0
See also other documents in the category Digilent Hardware:
- 410-282P-KIT (4 pages)
- 410-279P-KIT (26 pages)
- 410-258P-KIT (16 pages)
- 410-138P-KIT (28 pages)
- 410-178P-KIT (22 pages)
- 410-292P-KIT (29 pages)
- 410-274P-KIT (29 pages)
- 410-182P-KIT (22 pages)
- 410-134P-KIT (17 pages)
- 410-183P-KIT (19 pages)
- 410-155P-KIT (12 pages)
- 6015-410-001P-KIT (26 pages)
- 410-087P-KIT (164 pages)
- 410-146P-KIT (4 pages)
- 6003-410-000P-KIT (138 pages)
- XUPV2P (23 pages)
- 410-047-C2P-KIT (3 pages)
- WaveForms (85 pages)
- 410-297P-KIT (25 pages)
- 410-295P-KIT (37 pages)
- 410-296P-KIT (23 pages)
- 410-209P-KIT REV.D (16 pages)
- 410-209P-KIT REV.C (17 pages)
- 410-254P-KIT (17 pages)
- 410-280P-KIT (9 pages)
- 410-202P-KIT (20 pages)
- 410-273P-KIT (24 pages)
- 410-269P-KIT (11 pages)
- 410-216P-KIT (15 pages)
- 410-231P-KIT (4 pages)
- 410-211P-KIT (10 pages)
- 410-262P-KIT (8 pages)
- 410-229P (7 pages)
- 410-242P-KIT (4 pages)
- 6021-210-000P-KIT (27 pages)
- 410-185P-KIT (21 pages)
- 6032-410-000P-BOARD (4 pages)
- 410-174P (17 pages)
- 410-145P (6 pages)
- 210-264P-BOARD (3 pages)
- 6003-210-012P (27 pages)
- 410-236P-BOARD (2 pages)
- 410-163P (1 page)
- 410-097P-KIT (2 pages)
- 410-255P-KIT (1 page)