Pioneer CT-W505R User Manual
Ct-w505r, Operating instructions, Cid pioneer
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Operating
Instructions
STEREO DOUBLE CASSETTE DECK
CT-W505R
About the Demo mode (*)
Press the Deck II counter reset button (RESET) and the DECK II time counter
button (TIME/COUNT) simultaneously to set the demonstration mode. To
cancel the demonstration mode, press any one of the buttons enclosed in
the dotted lines above.
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will
know how to operate your unit properly. After you have fin
ished reading the instructions, keep them in a safe place for
future reference.
In some countries or regions, the shape of the power plug
and power outlet may sometimes differ from that shown in
the explanatory drawings. However, the method of connect
ing and operating the unit is the same.
WARNING:
to
prevent
fire
or
shock
hazard
,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIS
TURE.
IMPORTANT NOTICE
[For U.S. model]
The serial number for this equipment is located on the rear
panel. Please write this serial number on your enclosed war
ranty card and keep it in a secure area) This is for your secu
rity.
CAUTION
This product satisfies FCC regulations when shielded
cables and connectors are used fp connect the unit to
other equipment. To prevent electromagnetic interference
with electric appliances such as radios and televisions,
use shielded cables and connectors for connections.
This product complies with the Low Voltage Directive (73/23/
EEC), EMC Directives (89/336/EEC, 92/31/EEC) and CE Marking
Directive (93/68/EEC).
THE POWER SWITCH IS SECONDARY CONNECTED
AND THEREFORE DOES NOT SEPARATE THE UNIT
FROM MAINS POWER IN STANDBY POSITION.
IMPORTANT 1
A
The lightning flash with arrowhead, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated ’dangerous voltage' within the
product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK. DO
NOT
REMOVE
COVER
(OR
BACK).
NO
USER-SER
VICEABLE
PARTS
INSIDE.
REFER
SERVICING
TO
QUALIFIED SERVICE PERSONNEL.
A
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CiD PIONEER'
The Art of Entertainment
Document Outline
- Operating
- Instructions
- CT-W505R
- DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
- IMPORTANT NOTICE [For U.S. model]
- IMPORTANT 1
- A
- A
- IMPORTANT 2
- SAFETY INSTRUCTIONS
- CONDENSATION
- When installing the deck, avoid locations with high temperatures or humidity, and make sure that the deck receives adequate ventilation.
- Are the accidental erasure prevention tabs intact?
- Is the tape loose, or is some of the tape outside the cassette?
- CONTENTS
- CONNECTIONS
- CONTROL IN jack
- CONTROL OUT jack
- 0 POWER STANDBY/ON switch/indicator
- 0 FLEX button
- 0 DECK I counter reset button (RESET)
- 0 DECK i counter mode button (TIME/COUNT)
- © DOLBY* NR switch (B/OFF/C)
- Function display
- Synchro copy buttons (COPY l►il)
- BLE button ALCA button
- Reverse mode switch (REV MODE RELAY/SKIP) DECK II counter mode button (TIME/COUNT)
- DECK II counter reset button (RESET)
- CD'DECK SYNCHRO recording button (CD SYNC) DECK I eject button (A)
- Deck I operation buttons
- Recording level control (REC LEVEL)
- DECK II operation buttons
- DECK II eject button (^)
- One way mode zz position
- Two way mode r=> position
- Repeat mode co position (RELAYPLAY)
- ■ Dolby NR Systems
- ■ Dolby HX PRO Headroom Extension System
- FRONT PANEL FACILITIES
- Selecting DECK I
- Switching to DECK II
- G) DECK I counter indicator
- ® DOLBY NR B/C indicator (D AUTO indicator
- 0 Level meter
- (D CD'DECK SYNCHRO indicator (CD SYNC)
- ® DECK I tape transport mode indicators
- ® FLEX indicator
- ® Synchro copy indicator (COPY)
- ® AUTO BLE indicator
- DECK II counter indicator
- (Q) DECK II tape transport mode indicators
- For both DECK I and II
- DECK II only
- FRONT PANEL FACILITIES
- PLAYBACK
- 1. Load a prerecorded tape in DECK I or II.
- 2. Set the DOLBY NR switch.
- 3. Set the REV MODE switch (see page 8).
- 4. Set the stereo amplifier for tape playback.
- 5. Press the playback (► or -4) button of either DECK I or II.
- To improve high frequency sound during playback in tapes with poor recordings
- To stop playback temporarily (DECK II only)
- To stop playback
- 1. Load prerecorded tapes in DECK I and DECK II.
- 2. Set the DOLBY NR switch.
- 3. Set the REV MODE switch to czd (see page 11).
- 4. Set the stereo amplifier for tape playback.
- 5. Press the playback (► or -4) button of the deck that will start to play first.
- PLAYBACK (RELAY PLAYBACK)
- To improve high frequency sound during playback in tapes with poor recordings
- To stop playback temporarily (DECK II only)
- To stop playback
- PLAYBACK SEQUENCE WITH REV MODE SWITCH SETTING
- During forward playback
- During reverse playback
- From the stop mode
- How Selections are counted
- (See page 8 ALCA)
- 1. Load a tape for recording in DECK II.
- 2. Press the ALCA button.
- Error display
- The following illustrates the operation:
- Full automatic (Normal use)
- Semi automatic 1 (When the music peak level is already known)
- Semi automatic 2 (Setting the ALCA for every tune)
- 1. Set the REC LEVEL control to the MIN position.
- 2. Press the recording (•) button.
- 3. Press the playback (► or •*) button or the pause (ll) button.
- 1. Load a compact disc in the CD player.
- 2. Load the cassette for recording.
- 3. Set the REV MODE switch.
- 4. Set the DOLBY NR switch.
- 5. Press the play button of the CD player.
- 6. Adjust the recording level.
- 7. Press the stop (■) button of both the cassette deck and the CD player.
- 8. Press the CD SYNC button.
- When the compact disc finishes playing;
- When the end of the tape is reached while the CD player is still playing:
- If the auto-reverse function operates while the CD is still playing:
- 1. Load a tape for playback into DECK I and a tape for recording into DECK il.
- 2. Set the REV MODE switch.
- 3. Set the tape transport direction.
- 4. Press the SYNCHRO COPY button to select either NORMAL, HIGH speed, or TDNS.
- 4. Press the SYNCHRO COPY button to select either NORMAL or HiGH speed or TDNS.
- To stop copying
- To ciear all the memorized data and set the unit to its original data settings
- TROUBLESHOOTING