Pioneer CT-W505R - Manual (Page 14)

Semi automatic 2 (Setting the ALCA for every tune)
Press
ALGA
( Completion of \
ALCA tuning /
Press Press (First recording) Press
REG PLAY or PAUSE ^ Recording ^ STOP
Press Press (Second recording) Press
REG PLAY or.PAUSE ^ Recording ^ STOP
{ REPEAT)
With the ALCA system
• The REG LEVEL is adjusted to set the optimum recording level,
even in the REG PAUSE mode.
• When the STOP button is pressed, the recording level is reset to
the initial setting.
With this function, the optimum recording is possible.
RECORDING MUTE
Use this function to create the 4.5-second blanks needed for proper
operation of the music search function,
• Press the recording mute (O) button during recording and the
deck will create a blank space by recording a section which con­
tains no signal for approximately 4.5 seconds. The deck will then
enter recording standby mode.
NOTES:
• When the tape running direction is reversed during recording
mute operation (tape end is reached in forward direction), the re­
cording mute operation is cancelled and the deck enters the re­
cording mode.
• To create a blank which is more than 4.5 seconds long, hold the
button down for the desired length of time. When the button is
released, the deck will enter recording standby mode.
• To resume recording, press the pause (II) button or the playback
(► or ◄) button.
ERASING A TAPE
To erase the recorded contents of a tape, load the tape in DEGK II
and follow the procedure below.
1. Set the REC LEVEL control to the MIN position.
2. Press the recording (•) button.
3. Press the playback (► or •*) button or the pause (ll)
button.
CD*DECK SYNCHRO RECORDING
If the GD player has a program function to determine the order of
playback, program the GD player before beginning this operation.
1. Load a compact disc in the CD player.
2. Load the cassette for recording.
• Rewind the tape to the desired starting position.
14
En
3. Set the REV MODE switch.
• To record on one side only, set the switch to the rz position.
To record on both sides, set the switch to either the or
the cro position.
4. Set the DOLBY NR switch.
5. Press the play button of the CD player.
6. Adjust the recording level.
• See page 12.
7. Press the stop (■) button of both the cassette deck
and the CD player.
• Unless both this deck and the GD player are in stop mode,
synchro recording cannot be performed.
8. Press the CD SYNC button.
• The cassette deck begins recording, and the GD player begins
playback.
• Although recording begins when the GD SYNG button is
pressed, the GD player does not start playback until the button
is released. This function can be used to advance the tape
past the leader section, or to create a blank section on the
tape.
When the compact disc finishes playing;
The GD player enters stop mode and the cassette deck enters re­
cording standby mode. Ghange the disc and press the play button of
the GD player to resume recording. If the GD player does not resume
play within one minute, the cassette deck enters stop mode.
When the CD player changes discs
(twin tray or multi CD players):
The cassette deck enters recording standby mode, and resumes re­
cording when the GD player begins playing the next disc. A
foursecond blank space is automatically created between tracks.
When the end of the tape is reached while the CD player
is still playing:
The GD player returns to the beginning of the selection currentlyplay-
ing and then enters the pause mode. To resume recording, load an­
other tape and check the tape running indicator to ensure that the
tape is moving in the desired direction. If not, press the playback (►
or -M) button to change the tape direction, then immediately press
the stop (■) button. The tape running indicator will change direction.
Synchro recording can be resumed by pressing the GD SYNG button
again. (The GD SYNG button should be pressed within 1 minute. If
more than 1 minute elapses, the GD player will enter stop mode.)
If the auto-reverse function operates while the CD is still
playing:
The GD player returns to the beginning of the current selection and.
enters pause mode.
A ten-second blank space is automatically created on the reverse
side, then the GD player resumes playback and the deck resumes
recording.
NOTES:
• The CD»DECK SYNCHRO function only works with PIONEER CD
players equipped with the CD»DECK SYNCHRO function.
• Be sure to connect the deck and the CD player with the
CD»DECK SYNCHRO control cord.
• Only PIONEER CD players equipped with a CD»DECK SYNCHRO
jack can be used for CD*DECK SYNCHRO recording. Any type of
CD player which meets these requirements. Including twin-tray or
multi CD models, can be used.