beautypg.com

To replace warmer drawer, Setting warmer drawer controls, Cont’d) – Kenmore 790.9403 User Manual

Page 17

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

Setting Warmer Drawer Controls

(cont’d)

Warmer Drawer Recommended

Food Settings Table

Food Item

Setting

Bacon

HI

Hamburger Patties

HI

Poultry

HI

Pork Chops

HI

Fried Foods

HI

Pizza

HI

Gravies

MED

Casseroles

MED

Eggs

MED

Roasts (Beef, Pork, Lamb)

MED

Vegetables

MED

Biscuits

MED

Rolls, hard

MED

Pastries

MED

Rolls (soft)

LO

Empty Dinner Plates

LO

Puli up with finge.

Remove shield on right

glide. Pull up on left lever

while pushing down on

right lever.

Right Glide

Push down with finge

Fig. 1

Fig. 2

NOTE: The warmer drawer will

NOT

operate while inthe Self-Clean and ‘Oven

Lockout” modes

To Set the Warmer (Warm & Ready™) Drawer Thermostat
Control (some models)

The thermostat control is used to select the temperature of the warmer drawer.

It is located on the control panel (See Fig. 3 on previous page). To set the

thermostat, push in and turn the knob to the desired setting. The temperatures

are approximate, and are designated by HI, MED and LO.

1.

Turn the knob to select the desired temperature setting.

2.

For best results, preheat the drawer before adding food. An empty drawer

will preheat in approximately 15 minutes.

3.

Turn the thermostat control to

OFF

after use.

Warmer (Warm & Ready™) Drawer Temperature Selection

(some models)

Refer to the table in the side column for recommended settings. If a particular

food is not listed, start with the medium setting. If more crispness is desired,

remove the lid oraluminum foil.

Most foods can be kept at serving temperatures by using the medium setting.

When a combination of foods are to be kept warm (for instance, a meat with 2

vegetables and rolls), use the high setting.

Refrain from opening the warmer drawer while in use to eliminate loss of heat

from the drawer.

Warmer(Wanm & Ready™) Drawer IndicatorLight (some models)

The indicator light is located above the Warmer Drawer thermostat control. It

turns on when the control is set, and stays on until the control is turned OFF.

The warmer drawer is inoperable during the Self-Clean cycle. The indicator light

will not come on during the Self-Clean cycle.

To Remove and Replace Warmer (Warm & Ready™) Drawer
(some models)

To Remove Warmer Drawer:

^CAUTION

Turn power OFF before removing the warmer drawer.

2.

Open the drawer to the fully opened position.

3.

On the right glide you will find a shield attached with a hex-head screw (see

figure 1). Using a 1/4" socket and ratchet remove the shield.

4.

Locate glide lever on each side of drawer, pull upon the left glide lever and push

down on the rightglide lever.

5.

Pull the drawer away from the range.

To Replace Warmer Drawer:

1.

Replace shield on the right glide of the drawer body.

2.

Pull

the

bearing glides to the front

of the chassis glide (see figure 2).

3.

Align the glide on each side of the drawer with the glide slots on the range.

4.

Push the drawer into the range until levers “click” (approximately 2”). Pull the

drawer open again to seat bearing glides into position. If you

do not hearthe

levers “click” or the bearing glides do not feel seated remove the
drawer and repeat steps 2-4.

This will minimize possible damage to the

bearingglides.

A WARNING

Electrical Shock Hazard can occur and result in

serious injury or death. Disconnect appliance from electric power

before cleaning and servicing the warmer drawer.

17

This manual is related to the following products: