beautypg.com

Installation requirements, Tools needed for installation, Pedestal – Kenmore 110.4292 User Manual

Page 5: Stack kit

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

INSTALLATION REQUIREMENTS

Assemble the necessary tools and supplies before beginning the

washer installation. The parts supplied are In the washer drum.

Tools needed for connecting the water inlet hoses
■ Pliers (that open to 1 ®/i5 in. [39.5 mm])

■ Flashlight (optional)

Tools needed for installation
■ Open end wrench 17 mm and 13 mm

■ Level

■ Wood block (2"

X

4" [5.8

X

10.2 cm])

■ Ruler or measuring tape

Parts supplied

Beaded strap

Transport bolt hole plug (4)

Parts listed are available from your local Sears store or Sears
Service Center. For further information, please call
1-800-4-MY-HOME® (1-800-469-4663).

If You Have

You Will Need to Buy

Laundry tub or
standpipe taller

than 96 in. (2.4 m)

Sump pump system (if not already
available)

Overhead sewer

Standard 20 gal. (76 L), 30 In. (76.2 cm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)

Eloor drain

Siphon break, Part Number 285834;
additional drain hose Part
Number 8318155; and connector kit.
Part Number 285835

Drain hose too
short

4 ft drain hose extension kit, Part
Number 285863

Water faucets
beyond reach of
fill hoses

2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,

10 ft (3.0 m) Part Number 350021

Pedestal

A pedestal may be purchased separately for this washer. This
pedestal will add about 13 in. (33 cm) to the height of your unit
for a total vertical height of approximately 51 in. (130 cm).

This pedestal (with storage drawer) is available in three colors:

White - Part Number 42842

Bisque - Part Number 42844

Graphite - Part Number 42846

To order, call your local Sears store. For further information,
please cal 11-800-4-MY-HOME” (1-800-469-4663).

Stack Kit

Are you planning to stack your Kenmore HE3t washer and dryer?
To do so, find the stack kit (8541503) in the drum of the matching

Kenmore dryer.

Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”

Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area, (See “Drain
System.”)
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.

You will need

■ A water heater set to deliver 120°F (49°C) water to the

washer.

■ A grounded electrical outlet located within 5 ft (1.5 m) of

where fhe power cord is attached to the back of the washer.
(See “Electrical Requirements.”)

■ Hot and cold water faucets located within 4 ft (1.2 m) of the

hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).

■ A level floor with a maximum slope of 1 in. (2.5 cm) under

entire washer. Installing the washer on carpeting is not
recommended.

■ A sturdy and solid floor to support the washer with a total

weight (water and load) of 400 lbs (180 kg).

Do not operate your washer in temperatures below 32°E (0°C).
Some water can remain in the washer and can cause damage in
low temperatures.

This manual is related to the following products: