Checkline TI-25DL-MMX - Manual (Page 4)

– 4 –
3.2 Contents Of Kit
The TI-25M-MMX is supplied as a complete kit with the following:
a. Gauge
b. Two (2) AA batteries
(installed in gauge)
c. Probe/cable assembly
d. 4 oz. Bottle of coupling fluid
e. NIST-traceable calibration
certificate
f. Operating instruction manual
g. Foam-filled carrying case
3.3 Probe
The probe transmits and receives the ultrasonic sound waves which the
TI-25DL-MMX uses to calculate the thickness of the material being
measured. The probe must be used correctly in order for the
TI-25DL-MMX to produce accurate and reliable results.
A small amount of “coupling” fluid, commonly called “couplant” is used
to insure that there are no air gaps between the probe and the material
surface. Grasp the probe by the molded rubber grip and place it on top
of the material surface. Apply moderate pressure to the top surface of
the probe with your index finger (A) or thumb (B) to stabilize the probe
and to keep the wearface seated flat against the measurement surface.
a
d
c
e
g
Probe
Wearface
A B
– 29 –
1 7 .0 M AT ERI AL S AFET Y D ATA S H EET (M SDA)
Section 1— Product Identification
Product Name: TI-25M Generic Name: Ultrasonic Couplant
Manufacturer: Electromatic Equipt. Co. NFPA Hazardous Materials Identification System (est)
Health 0 Flammability 0 Reactivity 0
Section 2— Hazardous Ingredients
This material does not contain any ingredients having known health hazards in concentrations greater
than 1%. This material does not contain any known or suspected carcinogens.
Section 3 — Physical Data (nominal)
Boiling Point: >220°F Freezing Point: <20°F
Vapor Pressure: N/A Evaporation Rate: N/A
Specific Gravity: >1.0Z Solubility in Water: complete
pH: 7.35 – 7.9 Acoustic Imp.: 1.726x10 6
Vapor Density: N/A Appearance and Odor: water white, opaque gel; bland odor
Section 4 — Fire and Explosive Hazard Data
Flash Point: none Upper Exposure Limit: none Lower Exposure Limit: none
Special Fire Fighting Procedures: N/A
Extinguishing media: N/A
Unusual Fire and Explosion Hazards: none
Section 5 — Reactive Data
Stability: Stable Conditions to Avoid: none
Incompatibility (Materials to Avoid): none known
Hazardous Polymerization: will not occur
Hazardous Decomposition or Byproducts: none known
Section 6 —- Health Hazard and First Aid Data
Routes of Entry 1 :
Skin: not likely Ingestion: not normally Eyes: not normally Inhalation: no
Effects of Overexposure:
Acute: May cause temporary eye irritation
Chronic: none expected
First Aid Procedures:
Skin: Remove with water if desired.
Eyes: Flush with water for 15 minutes.
Ingestion: For large quantities, induce vomiting and call a physician Inhalation: N/A
Section 7 - Storage and Handling Information
Precautions to be taken in handling and storage: Store between 20 °F and 120 °F. Spills are
slippery and should be cleaned up immediately. Steps to be taken in case material is released or spilled:
Pick up excess for disposal. Clean with water. Waste disposal method: Dispose of in accordance with
federal, state, and local regulations.
Section 8 — Control Measures
Respiratory Protection: not required Ventilation: not required
Protective Gloves: on individuals demonstrating sensitivity to TI-25M
Eye Protection: as required by working conditions
Other Protective Equipment: not required
1. TI-25M-MMX contains only food grade and cosmetic grade ingredients.