Panasonic OMNIVISION PV-M2066 - Manual (Page 19)

Cancel a Timer Recording:
Recording Is in progress
Hold down the STOP button for a few
seconds to cancel the Timer Recording.
• Any future daily or weekly recordings will be
performed as programmed.
Replace Program Contents:
Recording is not in progress
Push the PROG
button to display
all currently
set programs.
Rotate and push
the Wheel to
select and enter
the desired timer
recording.
{See page 18.)
P DT STRAT STOP
1------------------------ : — CH SPD
3 10 8 OOp 9:00p to SP
4 SU 9:00p10:00p L SLP
SELECT -e;ROTATE WHEEL
ENTER PUSH WHEEL
CANCEL PUSH CLEAR KEY
END PUSH PROG KEY
DATE I> START STOP CH
8 SAT 10:OOP12:OOP 125
/ | S / | \
msB^tSSESB
BY ROTATING WHEEL
<-PUSH CLEAR : PUSH WHEEL-»
TO END PUSH PROG KEY
Rotate and push
the Wheel to select and enter
replacement information.
Push the PROG button to exit this
mode and return to the normal TV
screen.
Review or Clear Program Contents:
Recording is not in progress
P DT STRAT STOP CH SPD
2 8 1D;OOp 12:00p 125 SLP
3 10 B:00p 9:00p 10 SP
4 SU 9:00p10:00p L SLP
SELECT 1-8:ROTATE WHEEL
ENTER :PUSH WHEEL
CANCEL :PUSH CLEAR KEY
END : PUSH PROG KEY
Push the PROG
button to display
all currently set
programs.
Rotate the Wheel
to select the
desired program
number.
Push the CLEAR
button to clear the
program.
Push the PROG button to exit this
mode and return to the normal TV
screen.
P DT STRAT
D
2
STOP CH SPD
8 10:00p12:00p12s SLP
3 10 8:00p 9;00p 10 SP
4 SU 9:DOp1O;O0p L SLP
SELECT 1-B:ROTATE WHEEL
ENTER : PUSH WHEEL
END :PUSH PROG KEY
Timer Recording
Using Unit Buttons
A timer recording can be set up using the buttons on the
Combination VCR. If necessary, the clock can also be set.
Hold down
REC/TIME.
and
Push FF to
enter the
program mode.
START STOP CH
SLP
SELECT START DATE
BY SELECT A/¥ KEY
NEXT, PUSH SET KEY OR
TO END PUSH PROG KEY
MANUAL SET
• If the clock is not set, pushing
these buttons will display the SET
CLOCK screen. In this case, set
the clock according to the OSD’s
instructions and then set a timer
recording.
• Once the Combination VCR is in the Program mode, the
PLAY, REC, FF, and REW buttons on the Combination
VCR operate only as specified above.
........ SET CLOCK ..............
SELECT
SET
END
PUSH SELECT i/y
PUSH SET KEY
PUSH PROG KEY
or
(for down) (for up)
Push REW or PLAY to
make your selection.
Push FF to set
and move on to
the next item.
Push SET (FF) repeatedly to move to a
particular item for setting or correction.
Items to be Set:
• recording DATE
• START time
• STOP time
• CH(annel), or LINE
• SPEED (SP, LP, SLP)
When the program is completed...
and
Push REC/TIME
and FF to display
program contents.
(at the same time)
To set the next program,
repeat steps 2, 3, and 4 before continuing with step 5.
and
Push RECATIME and
FF to exit this mode.
(at the same time)
It is not possible to clear a timer program using the Combination
VCR buttons. Please use the Remote Control.
19