Panasonic PV-8665S - Manual (Page 35)

VCR PlusH- Programming
Easy Taping.
Ix^Check list before you begin.
□ The clock is set.
Q VCR Plus+ Setup is complete {see page 34),
1-
0 VV~-----
Multi Function Display
3
5
Q © ©
‘0 © ©
© © ©
® ©I
MceK
O CD O i
O
(Q
O \
«X cn I
O O'
■ADD/
DELETE
Use normal Timer Recording steps if:
• the PlusCode for a program is not listed.
• you anticipate the program, such as a sporting
event, to run over the scheduled stop time.
See page 23 to:
• cancel a timer recording in progress.
• replace program contents.
• review or clear program contents once set.
Important notes when using a DSS receiver
• When recording programs via a DSS receiver,
the DSS receiver must be left on,
• When recording programs via an antenna or
cable, the DSS receiver must be turned off.
1
Press PROG to display the
“SET PROGRAM” screen.
2
Press
AT
to select “VCR Plus+
PROGRAM,” and then press ►
to display the “VCR Plus+” screen.
---------- SET PROGRAM ----------------
VCR Plus+ PROGRAM
HMER PROGRAM
VCR PIUS+
ENTER PLUSCODE NUMBER
\ I /
/ I ^
USING 0-9 KEYS
END :PR0G KEY
O Press the NUMBERED keys to
enter the PlusCode number.
• Refer to your local TV listings.
To Make Corrections
Press
^
repeatedly to delete the
PlusCode number. Then, enter the correct number.
4
Press PROG to lock in your program.
VCR P1US+
ENTER PLUSCOOE NUMBER
123456
USING 0'-9 KEYS
BACKSPACE KEY
ENTER iPROG KEY
5
Press the 1,2 or 3 key to select
the program type.
G
Press
AT
and ► to select and
set each of the remaining items
as follows.
Remaining Items
• Category (N/A [not applicable], SPORTS,
MOVIE, COMEDY, MUSIC, DRAMA)
• Speed (SP, LP, SLP)
To Make Corrections
Repeatedly press ► to move the cursor
to the right, or A to move to the left to the
incorrect entry and make the correction.
7
Press PROG if contents are
acceptable.
To cancel program contents:
Press ADD/DLT.
VCR PIUS+
1 ONE TIME
2 DAILY(MON-FRI)
3 WEEKLY
TO SELECT PUSH 1.2 OR 3
DATE START STOP
iiiailigitilJM.
1.1
TODAY
CATEGORY :EDQ
SELECT CATEGORY
SELECT;* ▼ KEY
SET
;4 ► KEY
END :PR0G KEY
If you use connection type
“A" on paoe 12, the
channel shown in this on­
screen display will always
be the cable box output
channel number.
P DT START STOP CH SPD
1DAY 9:OOA12:OOA OS SP
3 --- --------:-----------
CANCEL:ADG/DLT KEY
SELECT 1*B:* T KEY
ENTER :► KEY
END :PROG KEY
8
Press PROG to complete
the program.
• If you’re using a Cable Box, make sure
that it is tuned to the desired channel
and the power is left on for timer recording.
TURN VCR OFF
FOR TIMER RECORDING
AND
LEAVE CABLE BOX POWER ON
This display may differ depending
on your cable box hook-up.
Press POWER off to set the timer.
Multi Function Display
You can obtain unlisted PlusCode numbers by calling 1 - 900 - 454 - 7587. Call costs approximately $.95
per minute.
VCR PlusCodes can not be used to program the VCR to record OSS channels.
Avoid overlapping program times.
An on-screen display will indicate if an invalid PlusCode number has been entered or when all timer
programs are full.
35