Panasonic NE-1757 - Manual (Page 10)

C. Programming Memory Pads for Single Stage Heating
The oven can not be programmed until the program lock feature is deactivated. Oven is locked if operation
starts by touching programmed pad without having to touch START pad.
(See page 12, G. To Activate Program Lock.)
1. Make sure the oven is plugged into a properly grounded electrical outlet.
—DO NOT OPEN THE DOOR—
-PflOG-
r
-pRim- ///-/'
3.
RH lU
k 1 mi
STAGE Ht
'PR^'
Rp
4.
mi
J
STAGE OEF
I
5.
-PROG- / n n
/
u u
-Ar "" ____ J
STAGE 0€F
PROG / nn'
6.
RH / LI LI
1 mi
J
STAGE DEF
<
7.
8.
-J
The display window MUST be blank before programming can begin.
If any indicator light is illuminated in the digital Display Window:
A. Close the door, touch STOP/RESET pad and wait 1 minute until the Display goes
blank.
B. Read cycle counter for any pad then quickly close the door if you desire to make
the display blank more quickly (see page 11, F).
2. Touch PROG pad. “PROG” sign will start to blink in the Display Window.
Do not keep pressing PROG pad for more than 5 seconds, or a false failure code may
result.
Touch Memory Pad you desire to reprogram. The pad number and the previously
selected time and Power Level will appear in the Display. “PROG" and the single stage
heating indicator “1 ” will blink.
[Example]: Touch Memory Pad Number 4.
Select the desired power level by touching the Power level Selector Pad.—the
selected power level will be displayed in the window and the Heating time display will go
blank.
[Example]: Touch the Power Level Selector Pad 3 times for DEFROST.
Set the desired heating time by touching the appropriate number pad in combination of
minutes and seconds desired. (Up to 15 min. on HI and MED—or 30 min. on DEF.)
[Example]: Fori minute touch pads 1,0 and 0.
Touch the PROG pad again. The “PROG” sign will stop blinking. This means that you
have completed reprogramming the selected Memory Pad for single stage heating.
Program the remaining Memory Pads as desired by repeating Step 2-7 above. DO
NOT OPEN THE OVEN DOOR while programming.
Note: When the “PROG" Display is blinking the program can be cancelled and/or the pad
erased by touching the STOP/RESET pad.
D. Programming Memory Pads for 2 Stage Heating
Do Not Open the Oven Door.
1. Complete steps 1 to 5 above. Do Not Touch the PROG pad.
-PROG- f I I n
f uu
mi
STAGE
-PHOG-
STAGE
PROG
RH
1 ___ 2
STAGE
-1
-PROG-
RH ^
L 1 -2- III! _______^
n n
U LI
n n
LI U
im
2. Select power level for the second stage by touching Power Level Selector Pad. The
selected power level will be displayed in the window and the second stage indicator “2”
will start to blink, indicating that the second stage is being programmed.
[Example]: Touch the Power Level Selector Pad 1 time for HIGH power.
Set the desired heating time by touching appropriate number pads. (Up to 15 min. on HI
and MED—or 30 min. on DEF.)
[Example]: For 2 minutes touch pads 2,0 and 0.
Touch the PROG pad again and the “PROG” sign will stop blinking and the STAGE
Indicators (1 and 2) will remain illuminated. The total time for both stages will be
displayed. This means that you have completed programming the desired Memory Pad
for 2 stage heating.
Three seconds after programming is completed, the display will go blank.
Program the remaining pads as desired by repeating the steps above. DO NOT OPEN
THE OVEN DOOR during programming.
-
10
-
3.
4.