Check list before you begin, Display set program, Display vcr plus+ screen – Panasonic PV-V4520 User Manual
Page 17: Enter pluscode programming number, Enter record frequency, Select record speed, End programming, Use normal timer recording steps if, Important notes for dss/cable box users, Vcr plus+system programming
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
‘Important: If the remote control POWER, ACTION, PROGA/CR+, CHA/V, NUMBERED keys,
INPUT, SEARCH or ADD/DLT button does not work when pressed, press the
VCR button on the remote and try the button again.
I^c
Check list before you begin.
Q The clock is set.
□ VCR Plus+ System Setup is complete (see pages 14-16).
Process of Recording
VCR Plus+System Programming
1
Connection О Setup|o
RSigpiffijDEtii©
Display SET PROGRAM.
Press PROGA/CR+.*
2
SET PROGRAM
VCR Ptus+ PROGRAMMING
TIMER PROGRAMMING
SELECT;* ▼ KEY
SET ;► KEY
END :PROG KEY
Display VCR Plus+
screen.
1) Press
AT
to select.
2) Press ►
to display.
3
VCR Plu5+ SYSTEM
ENTER PLUSCODE NUMBER
N ' /
/ \
USING 0-9 KEYS
To Make Corrections,
press A, repeatedly to delete the
PlusCode programming number.
VCR
PIUS+
SYSTEM
DAILY(MON-FRI)
WEEKLY
SELECT:* ▼ KEY
SET :► KEY
END ;PR0G KEY
Enter PlusCode
programming number.
1) Press
Numbered
keys.
2) Press PROG/
VCR+ to lock
in the program.
Enter record frequency.
1) Press AT to
select.
2) Press ► to set.
6
POWER
P SELECT/
. S E T
3
A
:PLAY
▼ :STOP
;
◄ :REW
4
► :FF
1
PROG/
‘ VCR+
CQUniP RtSCt OISPLAV TAF€ PQSNpN
CD CZ) О
OAUSC CM SKIP SPtED SEARCH.
GD О О ОI
SLOW
3 NUMBERED
keys
ADD/
DELETE
Model PV-V4520 remote is shown
here.
* T KEY
< ► KEY
PROG/ACTION KEY
Select record speed.
1) Press
AT
to
change.
2) Press ► to set.
5
P DT START STOP CH SPD
1 DAY 9:00A12:00A 08 SP
3 -------- :----------; —
4 -- --------- ---- ;---
CANCEL:AOD/DLT KEY
SELECT 1 - 8 : *
T
KEY
ENTER :► KEY
END
:PROG/ACT I ON KEY
End programming.
1) Press PROG/
VCR+
(or ACTION).
0
(vc To cancel
press ADD/DLT.
2) Press PROG/
VCR+
(or ACTION)
again to exit.
Use normal Timer Recording steps if:
• the PlusCode programming number for a
program is not listed.
• you anticipate the program, such as a
sporting event, to run over the scheduled
stop time.
See page 13 to:
• cancel a timer recording in progress.
• replace program contents.
• review or clear program contents once set.
Important notes for DSS/Cable Box users
• When recording via DSS, the receiver,
must be left on.
• When recording via cable or antenna,
DSS receiver must be off.
Set timer.
Press POWER off.
Multi Function Display
Avoid overlapping program times.
VCR PlusCode programming numbers
can not be used to program the VCR to
record DSS channels.
You can obtain unlisted PlusCode
numbers by calling 1 - 900 - 454 - 7587.
Call costs approximately $.95 per minute.
17