Clarion DXZ768RMP - Manual (Page 14)

14
DXZ768RMP
280-8334-00
English 6. OPERATIONS
Basic Operations
Note: Be sure to read this chapter referring to the front diagrams of
chapter “2. CONTROLS” on page 5 (unfold).
CAUTION
Be sure to lower the volume before
switching off the unit power or the ignition
key. The unit remembers its last volume
setting. If you switch the power off with the
volume up, when you switch the power back
on, the sudden loud volume may hurt your
hearing and damage the unit.
Turning on/off the power
Note:
• Be careful about using this unit for a long time without
running the engine. If you drain the car’s battery too
far, you may not be able to start the engine and this
can reduce the service life of the battery.
1. Press the [SRC] button.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3. Press and hold the [SRC] button for 1 second
or longer to turn off the power for the unit.
Note:
• System check
During the initial power up of this unit, it will go
through a system check procedure. This
procedure verifies any devices connected through
CeNET. Any additional CeNET devices plugged
into the unit after the initial power up will initiate
the system check procedure. When the power is
turned on, “SYSTEM CHECK” appears in the
display if the wire connections were modified. The
system check starts automatically within the unit.
Selecting a mode
1. Press the [SRC] button to change the
operation mode.
2. Each time you press the [SRC] button, the
operation mode changes in the following
order:
Radio mode ➜ DAB mode ➜ CD/MP3/WMA
mode ➜ CD changer (iPod BB) mode ➜
CD changer mode ➜ DVD changer mode
➜ TV mode ➜ AUX mode ➜ Radio mode...
∗ External equipment not connected through
CeNET will not be displayed.
Adjusting the volume
1. Press the front part of the [ROTARY] knob.
The knob will pop up.
2. Turn the [ROTARY] knob to adjust the volume.
∗ The volume level is from 0 (minimum) to 33
(maximum).
Switching the display
● When the power is turned on
1. Each time you press the [D] button, the
display switches in the following order:
Main display ➜ Title display ➜ Main
display ...
∗ In the case of a user title, only the top level is
displayed.
∗ In the case of TV/AUX/DVD changer, the
display cannot be switched to “title display”.
∗ Once selected, the preferred display becomes
the display default. When a function adjustment
such as volume is made, the screen will
momentarily switch to that function’s display,
then revert back to the preferred display
several seconds after the adjustment.
∗ When you have entered a title in a CD/MP3/
WMA, it appears in the display. If you have not
entered a title, “
” appears in the display. For
information on how to enter a title, refer to the
subsection “Entering titles” in the section
“Operations Common to Each Mode”.
2. Press and hold the [D] button for 4 seconds
or longer to turn off the display while in the
usual play. And press the button to return to
the previous mode.
CT (Clock Time) function
The CT function receives CT data sent from an
RDS station and displays the time.
∗ If a CT data is not being received, “– –:– –CT”
appears in the display.
Note:
• CT data is not transmitted in some countries and
by some broadcast stations. Also, in some areas,
the CT may not display accurately.
Setting MAGNA BASS EXTEND
The MAGNA BASS EXTEND does not adjust
the low frequencies like the normal sound
adjustment function, but emphasizes the deep
bass frequencies area to provide you with a
dynamic sound.
∗ The factory default setting is “OFF”.
1. Press and hold the [A-M] button for 1 second
or longer to turn on the MAGNA BASS
EXTEND effect. “MB” lights in the display.