B&M 45043 PRECISION SPORT SHIFTER - O4 + GTO User Manual
Page 6
Torque 1/4-20 bolts to 8-10 ft-lbs.
Caution do not overtorque bolts!!
Torque M8 thin nuts to 8-10 ft-lbs.
Torque M8 nuts to 15 ft-lbs.
Leave approx. 0.9" of M8 set
screw thread above GTO Trans
after locking down GTO Trans.
A S S E M B L Y
STEP 14. Install B&M shifter using (2) 1/4-20 bolts, (2) lock
washers, (2) M8 nuts, (2) M8 thin nuts and (2) M8
washers.
(SEE DIAGRAM BELOW FOR DETAILS)
TOOLS: Screwdriver (flat), Hex Wrench (6mm), thread
adhesive, and wrench (13mm)
NOTE: FAILURE TO USE THREAD ADHESIVE COULD
RESULT IN SHIFTER MALFUNCTION.
STEP 15. Reinstall rubber boot.
NOTE: On some earlier models a black boot was used
which may need some trimming of the opening to
allow for full gear engagement of 1, 3 & 5th gear.
Or you can replace the black boot with the newer
white boot, GM P/N: 92169196.
STEP 16. Install top stick
L
using (2) 5/16-18 bolts and
thread adhesive.
TOOL: 3/16 Hex and adhesive.
Torque bolts to 26 ft./lbs. (35 N/m)
NOTE: FAILURE TO USE THREAD ADHESIVE COULD
RESULT IN SHIFTER MALFUNCTION.
L
.9"
M8 NUT
M8 LOCKWASHER
M8 FLAT WASHER
B&M BASE
M8 THIN NUT
GTO TRANS
GTO TRANS GASKET
- 10225 SHIFT IMPROVER KIT (7 pages)
- 10227 TRANSPAK (8 pages)
- 50231 TRANSKIT (1 page)
- 10230 FLEXPLATE (1 page)
- 10280 CAST DEEP PAN (2 pages)
- 10300 DEEP PAN, CHRYSLER NAG-1 (3 pages)
- 10310 CAST ALUMINUM FRONT END COVER FOR DANA 30 IS CONSTRUCTED OF A356.0-T6 ALUMINUM. THIS RUGGED UNIT DIS (2 pages)
- 10311 CAST ALUMINUM REAR END COVER FOR DANA 35 WAS DESIGNED TO STRENGTHEN THE REAR END BY PREVENTING CASE (3 pages)
- 10312 Dana 44 Rear End Cover, A356.0-T6 Aluminum (3 pages)
- 10314 DANA 60/70 COVER WAS DESIGNED TO FIT BOTH DANA 60 AND DANA 70 DIFFERENTIALS. CONSTRUCTED OF A356.0-T (3 pages)
- 10315 Dana 80 cover was designed to strengthen the axle by preventing case distortion, ring gear & cap bea (3 pages)
- 10497 BRACKET & LEVER KIT (1 page)
- 117101 STRT TRANS TH700R4 CHV WITH MECH SP (7 pages)
- 120001 SHIFT PLUS 2 TRANS CONTROLLER (19 pages)
- 120002 TPS FOR CARBUERETED KITS (2 pages)
- 20260 SHIFT IMPROVER KIT (6 pages)
- 20261 SHIFT IMPROVER KIT (6 pages)
- 20280 CAST DEEP PAN (2 pages)
- 20297 KICKDOWN SWITCH KIT (1 page)
- 20480 NITROUS HOLESHOT 2400 (6 pages)
- 22300 NAG-1 Locking Trans Dipstick (2 pages)
- 30228 TRANSPAK (8 pages)
- 30262 SHIFT IMPROVER KIT (8 pages)
- 30280 CAST DEEP PAN (2 pages)
- 35229 TRANSPAK (8 pages)
- 35265 SHIFT IMPROVER KIT (8 pages)
- 35498 BRACKET AND LEVER KIT (2 pages)
- 40227 TRANSPAK (18 pages)
- 40263 SHIFT IMPROVER KIT (16 pages)
- 40281 CAST DEEP PAN (1 page)
- 40291 CAST DEEP PAN (2 pages)
- 40295 CAST DEEP PAN (2 pages)
- 40297 CAST ALUMINUM REAR END COVER, FORD 8.8 (3 pages)
- 40298 Cast Aluminum Rear End Cover for Ford 9.75 (3 pages)
- 40422 HOLESHOT 2400 C6 SMALL PILOT (6 pages)
- 40496 BRACKET AND LEVER KIT (3 pages)
- 40497 BRACKET AND LEVER KIT (2 pages)
- 40504 BRACKET AND LEVER KIT, 4R70W (7 pages)
- 40505 BRACKET AND LEVER KIT, 4R100/E40D (7 pages)
- 45034 PRECISION SPORT SHIFTER - 08 & UP CORVETTE C6 & Z06 (11 pages)
- 45043 PRECISION SPORT SHIFTER - O4 + GTO (1 page)
- 45044 PRECISION SPORT SHIFTER - C5 &C6 CORVETTE (15 pages)
- 45047 PRECISION SPORT SHIFTER - 88 - 00 HONDA (2 pages)
- 45048 PREC SHIFTER JEEP 99-01 JEEP WRANGL (12 pages)