Nikon F100 - Manual (Page 37)

73
Menu/Features of Custom Setting
—continued
Custom Setting
6 . Focus area selection changed to continuously in the same
direction (page 37)
Options: 0: Disabled (initial setting)
1 : Enabled
At default setting, the focus area can be selected by pressing the focus area
selector in the desired direction. However, it can be set to be changed
continuously in the same direction. For example, when the top of the focus
area selector is pressed, focus area continues to change from top, bottom,
middle and so on. With this option, focus area can be switched to the opposite
position without pressing the opposite position on the focus area selector.
7 . Auto Exposure Lock when shutter release button is lightly pressed
(page 54)
Options: 0: Disabled (initial setting)
1 : Enabled
At default setting, Auto Exposure Lock can be performed by pressing the ‚
button. However, Auto Exposure can be set to be locked by lightly pressing
the shutter release button.
8 . Film advance with closing the camera back (when power switch is
on) (page 21)
Options: 0: Disabled (initial setting)
1 : Enabled
At default setting, film advances to the first frame after it is loaded, the
camera back is closed and the shutter release button is fully depressed.
However, film advance can be set to start when the camera back is closed.
9 . Dynamic AF Mode with Closest Subject Priority in Single Servo AF
(page 39)
Options: 0: Enabled (initial setting)
1 : Disabled
At default setting, Dynamic AF Mode with Closest Subject Priority (page 39)
is activated when Dynamic AF mode is selected in Single Servo AF. However,
Dynamic AF Mode with Closest Subject Priority can be set to be disabled in
Single Servo AF.
10 .Dynamic AF Mode with Closest Subject Priority in Continuous
Servo AF (page 39)
Options: 0: Disabled (initial setting)
1 : Enabled
At default setting, selecting Dynamic AF in Continuous Servo AF does not
activate Dynamic AF Mode with Closest Subject Priority (page 39). However,
Dynamic AF Mode with Closest Subject Priority can be set to be activated in
Continuous Servo AF.
11 .Auto Exposure/Flash Exposure Bracketing options (page 57)
Options: AS: Simultaneous activation of Auto Exposure/Flash Exposure
Bracketing (initial setting)
AE : Only Auto Exposure Bracketing activated
Sb : Only Flash Exposure Bracketing activated
At default setting, Auto Exposure and Flash Exposure Bracketing are
activated simultaneously. However, only Auto Exposure or Flash Exposure
Bracketing can be set to be activated.
12 .Switching Command Dial operations (pages 48-53)
Options: 0: Disabled (initial setting)
1 : Enabled
Unlike the default Command Dial operations, the Sub-Command Dial can be
set to select shutter speed (in Shutter-Priority Auto or Manual exposure
mode) and the Main-Command Dial to select aperture (in Aperture-Priority
Auto or Manual exposure mode).
13 .Easy Exposure Compensation (page 56)
Options: 0: Disabled (initial setting)
1 : Enabled
When the Easy Exposure Compensation is activated, exposure
compensation can be performed, without pressing the ˚ button, by
simply rotating the Sub-Command Dial (in Programmed Auto or Shutter-
Priority Auto exposure mode) or Main-Command Dial (in Aperture-Priority
Auto or Manual exposure mode).
• If the exposure compensation values are set to change in Custom Setting
menu 2, up/down to ±5 EV in 1/2 or 1 steps can be set.
• If the Command Dial operations are switched in Custom Setting menu 12,
Main- and Sub-Command Dials operate under opposite conditions except
in Programmed Auto exposure mode.
14 .Film advance in multiple exposure (page 61)
Options: 0: Single frame shooting (initial setting)
1 : Continuous shooting
At default setting, the shutter is released once each time the shutter release
button is fully depressed in multiple exposure (single frame shooting).
However, it can be changed to continuous shooting where the shutter can be
continuously released as long as the shutter release button is fully
depressed.
72
P500 (E) 02.12.27 5:48 PM Page 72
WWW.LENSINC.NET