E-flite Shoestring 15e ARF - Manual (Page 4)

4 E-flite Shoestring 15e ARF Assembly Manual
Contents of Kit/parts Layout
Replacement parts
EFL420501 Fuselage with Hatch
EFL420502 Main Wing Set with Ailerons
EFL420503 Tail Set
EFL420504 Landing Gear with Axle
EFL420505 Wheel pants set (painted)
EFL420506 EP Standoff set (8pcs)
EFL420507 Cowl (painted)
EFL420508 Wing tube
EFL420509 Fuselage hatch
EFL420510 Hardware Bag
EFL420511 Landing Gear with Axles
EFL420512 Wing Mounting Clips
Covering Colors
Midnight Blue HANU885
Sky Blue HANU875
Bright Yellow HANU872
hardware/Accessory Sizes
Main wheel 2-inch (52mm)
Tail wheel 1/2-inch (13mm)
Before Starting Assembly
Before beginning the assembly of your model, remove
each part from its bag for inspection. Closely inspect
the fuselage, wing panels, rudder and stabilizer for
damage. If you find any damaged or missing parts,
contact the place of purchase.
If you find any wrinkles in the covering, use a heat gun
(HAN100) and covering glove (HAN150) or covering
iron (HAN101) with a sealing iron sock (HAN141) to
remove them. Use caution while working around seams
or areas where the colors overlap to prevent pulling
the seams.
Recommended Radio Equipment
You will need a minimum 4-channel transmitter,
receiver and four servos.
Recommended Transmitter
SPMR5510 DX5e DSMX ® 5-Channel
Transmitter Only
Additional Items
SPMAR7010 AR7010 7-Channel DSMX
Receiver
SPMSA5030 Mini Digital Aircraft Servo (2)
JRPS388 Digital Micro Metal
Gear Servo (2)
SPMA3001 6-inch (152mm) Servo
Extension (2)
Recommended Sport Setup
Motor: Power 15 Brushless 975Kv
Outrunner (EFLM4015A)
Speed Control: 40A Pro Switch-Mode BEC BL
ESC (EFLA1040)
Battery: 3200mAh 3S 11.1V 30C Li-Po
Battery (EFLB32003S30)
Spinner: 1.5-inch Aluminum Bullet
Spinner (EFLSP150B)
Propeller: 10 x 10E (APC10010E)
Recommended Racing Setup
Motor: Power 25 BL 1250Kv
Outrunner (EFLM4025B)
Speed Control: 60A Pro Switch-Mode BEC BL
ESC (EFLA1060)
Battery: 4S 14.4V 30C Li-Po Battery
(EFLB25004S30)
Spinner: 1.5-inch Aluminum Bullet
Spinner (EFLSP150B)
Propeller: 8 x 8E (APC08080E)
Optional Accessories
EFLA110 Power Meter
EFLC3025 Celectra ™ 80W AC/DC Multi-
Chemistry Battery Charger
Required Tools and Adhesives
Tools & Equipment
Drill Epoxy brush
Felt-tipped pen Flat blade screwdriver
Low-tack tape Light machine oil
Long nose pliers Mixing cup
Mixing sticks Needle nose pliers
Paper towels Pencil
Pin vise Phillips screwdriver: #1, #2
Rubbing alcohol Ruler
Sandpaper T-pins
Side cutter Square
Straight edge Toothpicks
Balancing stand (optional)
Open end or box wrench: 10mm, 13mm
Hook and loop strap (EFLH1444)
Hook and loop tape (DUB348)
Hobby knife with #11 blade
Hex wrench or ball driver: 2.5mm, 3/32-inch, 3mm
Drill bit: 1/32-inch (1mm), 1/16-inch (1.5mm),
5/64-inch (2mm), 1/8-inch (3mm),
5/32-inch (4mm)
Adhesives
Medium CA PAAPT02
Thin CA PAAPT08
Threadlock PAAPT42
30-minute epoxy PAAPT39
Plastic Tape, Clear, 3/4 x 125-inch MMM190CL