Banner U-GAGE S18U Series—Analog - Manual (Page 7)

P/N 110738 rev. A
7
U-GAGE ™ S18U Series Sensor — Analog Output
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Sensing Range 30 to 300 mm (1.2" to 11.8")
Supply Voltage 10 to 30V dc (10% maximum ripple); 65 mA max. (exclusive of load), 40 mA typical @ 25V input
Ultrasonic Frequency 300 kHz, rep. rate 2.5 ms
Supply Protection Circuitry Protected against reverse polarity and transient voltages
Output Configuration Analog Output: 0 to 10V dc or 4 to 20 mA, depending on model
Output Protection Protected against short circuit conditions
Output Ratings Analog Voltage Output: 2.5 kΩ minimum load resistance
Minimum supply for a full 10V output is 12V dc (for supply voltages between 10
and 12, V out max is at least V supply -2)
Analog Current Output: 1 kΩ max @ 24V input
Max load resistance = (Vcc-4)/0.02 ohms
For current output (4-20 mA) models, ideal results are achieved when the total load resistance
R = [(Vin – 3)/0.020]Ω. Example, at Vin = 24V dc, R ≈ 1 kΩ (1 watt). A worst-case shift of 1% of sensing
distance is caused by operating the sensor at Vin = 30V dc and R = 0 Ω.
Output Response Time
(for a 95% step change)
2.5 milliseconds: Black wire at 5-30V dc
30 milliseconds: Black wire at 0-2V dc (or open)
Consult factory for other response speed options
Delay at Power-Up 300 milliseconds
Temperature Effect 0.02% of distance/ °C
Linearity* 2.5 ms response: ±1 mm 30 ms response: ± 0.5 mm
Resolution* 2.5 ms response: 1 mm 30 ms response: 0.5 mm
Minimum Window Size 5 mm
Adjustments Sensing window limits: TEACH-Mode programming of near and far window limits may be set using the
push button or remotely via TEACH input (see page 3).
Indicators Range Indicator (Red/Green) Green — Target is within sensing range
Red — Target is outside sensing range
OFF — Sensing power is OFF
Teach/Output Indicator (Yellow/Red) Yellow — Target is within taught limits
OFF — Target is outside taught window limits
Red — Sensor is in TEACH mode
Remote TEACH Input Impedance: 12 kΩ
Construction Threaded Barrel: Thermoplastic polyester Push Button Housing: ABS/PC
Push Button: Santoprene Lightpipes: Acrylic
Operating Conditions Temperature: -20° to +60° C (-4° to +140° F) Maximum relative humidity: 100%
Connections 2 m (6.5') or 9 m (30') shielded 5-conductor (with drain) PVC jacketed attached cable or 5-pin
Euro-style quick-disconnect (see page 10 for quick-disconnect cable options)
Environmental Rating Leakproof design is rated IEC IP67; NEMA 6P
Vibration and Mechanical
Shock
All models meet Mil. Std. 202F requirements method 201A (vibration: 10 to 60 Hz max., double amplitude
0.06", maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G 11 ms duration, half sine
wave.
Temperature Warmup Drift Less than 1.7% of sensing distance upon power-up (see Temperature Compensation, page 2)
Application Notes Objects passing inside the specified near limit may produce a false response.
Certifications
Specifications
* Linearity and resolution are specified using a 50 mm x 50 mm (2" x 2") aluminum plate at 22°C under fixed sensing conditions.
B