Banner Q40 Series - Manual (Page 4)

Output Configuration
SPDT solid-state dc switch; Choose NPN (current sinking) or PNP (cur-
rent sourcing) models
Light Operate: N.O. output conducts when sensor sees its own (or the
emitter's) modulated light
Dark Operate: N.C. output conducts when the sensor sees dark; the
N.C. (normally closed) output may be wired as a normally open marginal
signal alarm output, depending upon hookup to power supply (U.S. pat-
ent 5087838)
Output Rating
150 mA maximum (each) in standard hookup.
When wired for alarm output, the total load may not exceed 150 mA.
OFF-state leakage current: < 1 microamp @ 30V dc
ON-state saturation voltage: < 1V at 10 mA dc; < 1.5V at 150 mA dc
Output Protection Circuitry
Protected against false pulse on power-up and continuous overload or
short circuit of outputs
Output Response Time
Opposed mode: 3 ms ON, 1.5 ms OFF
Retro and Fixed-Field: 3 ms ON and OFF
NOTE: 100 ms delay on power-up; outputs do not conduct during this
time.
Construction
PBT polyester housing; acrylic lens
Environmental Rating
Leakproof design rated NEMA 6P, IEC IP67. QD Models rated IP69K per
DIN 40050-9.
Connections
2 m (6.5') or 9 m (30') attached cable, or 4-pin Euro-style quick-discon-
nect fitting
Operating Conditions
Temperature: -40° to +70°C (-40° to 158°F)
Maximum relative humidity: 90% at 50°C (non-condensing)
Vibration and Mechanical Shock
All models meet Mil. Std. 202F requirements. Method 201A (Vibration;
frequency 10 to 60 Hz, max., double amplitude 0.06" acceleration 10G).
Method 213B conditions H&I (Shock: 75G with unit operating; 100G for
non-operation)
Certifications
Quick-Disconnect (QD) Cables
4-Pin Threaded M12/Euro-Style Cordsets
Model Length Style Dimensions Pinout
MQDC-406 1.83 m
Straight
M12 x 1
ø 15 mm
(0.6")
44 mm max.
(1.7")
2
3
4
1
1 = Brown
2 = White
3 = Blue
4 = Black
MQDC-415 4.57 m
MQDC-430 9.14 m
MQDC-450 15.2 m
MQDC-406RA 1.83 m
Right-Angle
38 mm max.
(1.5")
M12 x 1
ø 15 mm
(0.6")
38 mm max.
(1.5")
MQDC-415RA 4.57 m
MQDC-430RA 9.14 m
MQDC-450RA 15.2 m
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE,
COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSE-
QUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARIS-
ING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp.
Q40 Sensors - dc-Voltage Series Installation Guide