Rockwell Automation 42GR Series 9000 LaserSight - Manual

Installation Instructions
Series 9000 LaserSight Photoelectric Sensors
IMPORTANT: SAVE THESE INSTRUCTIONS FOR FUTURE USE.
Refer to the product catalog pages for additional information.
Description
The LaserSight 9000 is a Class 1 visible red laser sensor designed for the
detection of small parts in the packaging, material handling and
semi-conductor industries. This sensor offers multiple sensing
modes suitable for general purpose detection that can be easily
set up by using the single-turn potentiometer and the highly
visible user interface.
Features
• Small spot size suitable for high precision sensing
• Class 1 visible laser beam for ease of alignment
• Precision long distance object detection in polarized and
transmitted beam sensing modes
• Selectable light operate or dark operate
• Solid-state DC output and SPDT relay output models
• IP69K rated
Class 1
Lasers that are safe under reasonably foreseeable conditions of
operation, including the use of optical instruments for intrabeam
viewing.
Reference IEC 60825-1:2007.
Class 1 Laser Characteristics
(see specifications)For Safe Laser Use:
• Do not permit a person to stare at the laser from within the
beam.
• Do not point the laser at a person's eye at close range.
• Locate open laser beam paths either above or below eye level,
where practical.
Use of control or adjustments or
performance of procedures other
than those specified herein may
result in hazardous radiation
exposure. Do NOT attempt to
disassemble this sensor for
repair. A defective unit must be
returned to the manufacturer.
Class I Laser Product
Complies with 21 CFR
1040.10 and 1040.11
except for deviations
pursuant to Laser
Notice No. 50, dated
June 24, 2007.
Description of Laser Class
CAUTION…Do not
disassemble for
repair
Specifications 
 Refer to product catalog pages for product selection guidelines
(www.ab.com/sensors).
Certifications
cULus and CE Marked for all applicable
directives
Environmental
Operating Environment
IP69K, NEMA 3, 4X, 6P, IP67 with 1200 psi
washdown
Operating Temperature
[C (F)]
-10…+50° (14…122°)
Vibration
10…55Hz, 1 mm amplitude; meets or exceeds
IEC 60947-5-2
Shock
30 g with 11 ms pulse duration, meets or
exceeds IEC 60947-5-2
Relative Humidity 5…95% (noncondensing)
Ambient Light Immunity 5000 Lux (Incandescent light)
Optical
Sensing Modes Sensing Range
Spot Size @
max. distance
Standard Diffuse
1…800 mm
(0.03…31.5 in.)
2.0 x 3.5 mm
(0.08 x 0.14 in.)
Polarized
Retroreflective 0.3…40 m
(1…130 ft)
20 x 25 mm
(0.79 x 0.98 in.)
Transmitted Beam 300 m (1000 ft)
140 x 175 mm
(5.5 x 6.89 in.)
Light Source Visible red laser (650 nm)
Electrical
Voltage 10…30V DC, 105…132V AC, 70…264V AC/DC
Current Consumption
45mA max (DC), 10 mA max (AC/DC),
70 mA max (AC)
Sensor Protection
DC: Overload and short circuit, reverse polarity
and false pulse
Outputs
Response Time
0.5 ms (diffuse, polarized retroreflective)
25 ms (SPDT relay) max.
Output Type PNP and NPN, SPDT EM relay
Output Mode Light or dark operate selectable
Output Current
250 mA (DC), PNP/NPN 250 mA DC relay: 2 A @
120V AC; 1 A @ 240V AC; 3 A @ 28V DC
Mechanical
Housing Material Valox®
Lens Material Acrylic
Connector Material Neoprene
Connection Types
2 m cable, 4-pin DC micro (M12) QD, 4-pin DC
mini
Supplied Accessories Mounting brackets, cordsets, reflectors