Rockwell Automation 500LG Control Module Kit - Manual (Page 2)

Renewal Parts
Wiring Diagram
42052-193-01 (1)
Printed in U.S.A.
PART
NO.
MATERIAL
CHG.
CHAR. SIZE
-01 1
TWO SIDES PRINTED
8-1/2" W x 11" H 4-1/4" W x 5-1/2" H
FLAT FOLDED
BODY STOCK WHITE
BODY INK BLACK
12 - 24 VDC 500LG-47CM12
24 VAC / 60/50 Hz 500LG-47CM24
110 - 120 VAC / 60/50 Hz 500LG-47CM120
200 - 277 VAC / 60/50 Hz 500LG-47CM277
12 - 24 VDC 500LG-48CM12
24 VAC / 60/50 Hz 500LG-48CM24
110 - 120 VAC / 60/50 Hz 500LG-48CM120
200 - 277 VAC / 60/50 Hz 500LG-48CM277
1 NO / NC 500LG-141C
2 NO / NC 500LG-142C
Control Module Kit
2 Wire
Voltage Cat. No.
3 Wire
Auxiliary Contact
FUSE
2
FUSE
COIL
VOLTAGE
P1 P2 P3 P4 P5
C
A2 A1
C
C
ON
OFF
(LEFT AUX.)
(RIGHT AUX.)
OFF ON R G
OFF ON R G
OFF ON R G
OFF ON R G
C C
2
P
N
P1 P2 P3 P4 P5
C
A2 A1
FUSE
2
FUSE
COIL
VOLTAGE
C
C
(LEFT AUX.)
(RIGHT AUX.)
C C
2
P
N
OFF ON
P1 P2 P3 P4 P5
ELECTRONIC MODULE
C
A1 A2
C
FUSE
2
FUSE
COIL
VOLTAGE
2
C C
P
N
OFF ON
P1 P2 P3 P4 P5
C
A1 A2
C
FUSE
2
FUSE
COIL
VOLTAGE
2
C C
P
N
OFF
HAND AUTO
TABLE D: OPTIONAL WIRING AND PILOT DEVICES FOR MECHANICALLY-HELD CONTACTOR, 3-WIRE CONTROL
TABLE B: OPTIONAL WIRING AND PILOT DEVICES FOR MECHANICALLY-HELD CONTACTOR, 2-WIRE CONTROL
OFF-ON OFF-AUTO SELECTOR SWITCH
HAND-OFF-AUTO ON-OFF-AUTO SELECTOR SWITCH
ON-OFF PUSHBUTTON
OFF-ON SELECTOR SWITCH
CONTROL VOLTAGE
CONTROL VOLTAGE
CONTROL VOLTAGE
CONTROL VOLTAGE
500LG(MECHANICALLY-HELD, 3-WIRE)
(OPTIONAL AUX.) (OPTIONAL AUX.)
500LG(MECHANICALLY-HELD, 2-WIRE)
C
ELECTRONIC
P2 P1
A1
P4 P3
MODULE
P5
A2
(OPTIONAL AUX.) (OPTIONAL AUX.)
CONTROL
VOLTAGE N P
P N
TABLE A: 2-WIRE CONNECTION DIAGRAM
TABLE C: 3-WIRE CONNECTION DIAGRAM
(RIGHT AUX.) (LEFT AUX.)
(RIGHT AUX.) (LEFT AUX.)
(RIGHT AUX.)
(LEFT AUX.)
(RIGHT AUX.)
(LEFT AUX.)
NOT
USED
COIL
VOLTAGE
ELECTRONIC MODULE
ELECTRONIC MODULE
ELECTRONIC MODULE
3
C
ELECTRONIC
P2 P1
A1
P4 P3
MODULE
P5
A2
CONTROL
VOLTAGE
N P
P N COIL
VOLTAGE
3
3
1
P
N
3
3
P
N
3
3
P
N
3 3
P
N
3
3
2 2
BULLETIN 500LG
LIGHTING CONTACTOR CONTROL MODULE KIT
INSTRUCTION SHEET
1 1031018
42052-193
OF
N/A
N/A
N/A
REVISION
AUTHORIZATION
DR.
CHKD.
APPD.
DATE
DATE
DATE
E - DOC
LOCATION: MILWAUKEE, WISCONSIN U.S.A.
B-vertical.ai
DWG.
SIZE
SHEET
B
1 2 3 4 5 6 7 8
A
B
C
D
E
G
H
REFERENCE
DIMENSIONS APPLY BEFORE
SURFACE TREATMENT
(DIMENSIONS IN INCHES)
TOLERANCES UNLESS
OTHERWISE SPECIFIED
.XX:
.XXX:
ANGLES:
42052
- - - - - - - - - - - - - -
- - - - - - -
- - - - - - -
- - - - - - -
- - - - - - -
THIS DRAWING IS THE PROPERTY OF
ROCKWELL AUTOMATION, INC.
OR ITS SUBSIDIARIES AND MAY NOT BE COPIED,
USED OR DISCLOSED FOR ANY PURPOSE
EXCEPT AS AUTHORIZED IN WRITING BY
ROCKWELL AUTOMATION, INC.
NOTICE 1 Remote device
2 Additional Control Circuit Overcurrent Protection may be required when the control circuit conductors extend beyond the
enclosure. Refer to the U.S. National Electrical Code or the Canadian Electrical Code for control circuit protection
requirements.
3 Coil and control voltages may not be the same. Check the voltage of the electronic module and coil before applying power.