Rockwell Automation 800T_H Pushbutton - Manual

1 2
BULLETIN 800H / T PUSHBUTTON
INSTALLATION INSTRUCTION SHEET
3 1010415
4 1017238
40061-059
OF
N/A
N/A
N/A
REVISION
AUTHORIZATION
DR.
CHKD.
APPD.
DATE
DATE
DATE
E - DOC
LOCATION: MILWAUKEE, WISCONSIN U.S.A.
B-vertical.ai
DWG.
SIZE
SHEET
B
1 2 3 4 5 6 7 8
A
B
C
D
E
F
G
H
REFERENCE
DIMENSIONS APPLY BEFORE
SURFACE TREATMENT
(DIMENSIONS IN INCHES)
TOLERANCES UNLESS
OTHERWISE SPECIFIED
.XX:
.XXX:
ANGLES:
40061
G. Ushakow 9-28-05
9-28-05
9-28-05
M. Jutz
E. Byaliy
ATTENTION: To prevent electrical
shock, disconnect from power source
before installing or servicing.
(Cat 800H-_ _ _, 800T-_ _ _)
Push Button Installation and Mounting Instructions
Instructions de montage et d'installation du bouton-poussoir
Drucktaster, einbau- und montageanleitung
Instrucciones de instacion y montaje de los pulsadores
Instuções de instalação e montagem do botão de pressão
THIS DRAWING IS THE PROPERTY OF
ROCKWELL AUTOMATION, INC.
OR ITS SUBSIDIARIES AND MAY NOT BE COPIED,
USED OR DISCLOSED FOR ANY PURPOSE
EXCEPT AS AUTHORIZED IN WRITING BY
ROCKWELL AUTOMATION, INC.
1/4 ш
(ш 6.4)
43/64"
(17.1)
1/2"
(12.7)
11/64"
(4.4)
1/2"
(12.7)
Minimum
Minimo
Metallic
Metallique
Metall
Metalico
Electrical Clearance to Metal Enclosure
Decacement electrique de l'acces au coffret de metal
Mindestabstand elektr. Klemmen/metalllgehäuse
Huelco minimo entre las bornas y la caja metallica
Distância livre des ligações eléctricas à caixa metálica
9/16"
(14.3)
Optional
En option
Option
Opcional
1-13/64 ш
(ш 30.6)
A
A
B
B
25 - 30 lb-in
(2.8 - 3.4 N·m)
800T-N245
800T-N3
16 Gage - 1/16" (1.6)
800T Series T 800H
3
2
1
5
4
3
2
12 Gage - 7/64" (2.8)
10 Gage - 9/64" (3.6)
3/16" (4.8)
1/4" (6.4)
> 1/4" (6.4)
Panel thickness
Epaisseur du panneau
Stärke derTafel
Grosor del panel
Espessura do painel Number of gaskets
Nombre de joints d'étanchéité
Anzahl der Dichtungen
Número de juntas
Número de juntas vedantes
inch (mm)
t
t
N
(Counterbore)
1 > 3/16" (4.8)
800T-XA2
800T-XAP
800T-XD1P
800T-XD2P
800T-XD5
800T-XD6
800T-XAP
800T-XD1P
800T-XD2P
1/4"
(6)
#8-32 UNC
When Required
Le cas échéant
Nach bedarf
Si fuera necesario
Quando necessàrio
Apply wet soap to boot lip before installing
Appliquer du savon emulsionne au capuchon avant l'installation
Vor der installation nasse seife auf dichtungslippe auftragen
Unte la guarnicion con jabon humedo antes de instalabla
Coloque uma solução de sabão na vedação antes da instalação
1-53/64"
(46.4)
1-1/2"
(38.1)
2-1/4"
(57.2)
1-27/32"
(46.8)
2-1/4"
(57.2)
1-27/32"
(46.8)
2-1/4"
(57.2)
2-1/2"
(63.5)
2-1/2"
(63.5)
2-1/2"
(63.5)
1-53/64"
(46.4)
1-53/64"
(46.4)
2-7/16"
(61.9)
2-7/16"
(61.9)
2-7/16"
(61.9)