Ps7060 multiquip saw — installing the blade, Caution, Warning – Multiquip PS706036 User Manual
Page 27
PS7060 MULTIQUIP SAW • OPERATION MANUAL — REV. #2 (06/02/08) — PAGE 27
An improperly torqued Mounting Bolt can cause the inside
diameter of the Blade, Blade Shaft, and Flange Bushing to
quickly wear. This can result in poor cutting characteristics
or premature failure of these parts requiring replacement
and machine "downtime".
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
Figure 13. Blade Wrench
125-175 lbs. (56.7 -79.4 Kg) of weight applied to
the end of the blade wrench will provide 125-175
ft. lbs. (169.5 -237.3 Nm) of torque to the blade
mounting bolt. (Figure 13.)
PS7060 MULTIQUIP SAW — INSTALLING THE BLADE
Figure 14. Torque Flange Bolt
6.
Lower the blade to the ground surface (A in Figure 14) to
prevent blade from spinning and tighten the mounting bolt
to 125-175 ft. lbs. (169.5 -237.3 Nm) of torque. (Item B in
Figure14.)
Stacking Blades for Wide Cuts
Combining, or stacking blades together to make wide cuts requires
and optional Bushing Extension Kit.
NEVER attempt to stack blades beyond the capacity of the
kits described here. NEVER operate the saw without blade
guards in place.
WARNING
WARNING
WARNING
WARNING
WARNING
■ Kit #18501 allows blade stacking from .375" to .75" thickness.
■ Kit #18502 allows blade stacking from .75" to 1.125" thickness.
1.
Remove existing blade. (See previous section.)
2.
Replace the standard Flange Bushing, Outer Flange, and
Mounting Bolt that came with the saw, with the extended
Bolt and Bushing and the new Outer Flange supplied with
the kit. Remember that the Mounting Bolt for the right side
of the saw has a left-hand thread while the Mounting Bolt
for the left side of the saw has a right-hand thread.
3.
Insert the Bushing and Mounting Bolt through the Outer
Flange and stack of Blades. Spacers are required between
blades when stacking multiple blades. The longer bushing
and bolt allow blades to be stacked together while
maintaining proper alignment of Flange Bushing into Blade
Shaft.
4.
Align Flange Pin through the stack of blades into the Inner
Flange.
5.
Tighten the 5/8" Mounting Bolt to 125-175 ft. lbs. of torque.
1
2
1.
12 In. (30.48 cm)
2.
125-175 lbs (56.7-79.4 Kg)
A
B
t
r
a
h
C
g
n
i
z
i
S
d
r
a
u
G
/
e
d
a
l
B
d
r
a
u
G
e
d
a
l
B
"
6
1
"
0
2
"
6
2
"
0
3
"
6
3
d
n
o
m
a
i
D
e
d
a
l
B
)
.
n
i
(
r
e
t
e
m
a
i
D
"
4
1
"
6
1
"
4
2
"
4
2
"
6
2
"
6
1
"
8
1
"
6
2
"
6
2
"
0
3
"
0
2
"
0
3
"
6
3
The operator must match the diamond blade diameter
to the proper blade guard size. See Blade/Guard Sizing
Chart.
WARNING
WARNING
WARNING
WARNING
WARNING