Purenex Multipure Aquaperform - Manual (Page 20)

Resetting the Capacity Monitor
After changing the drinking water system filter, the capacity monitor must be reset to its original capacity.
1. Press and hold the check/reset button on the Filter Monitor unit (FMu) for three (3) seconds. You should hear a long
audible sound.
2. The leD on the leD Display Plate will blink green for one (1) second with an audible sound, then blink green and red
for one (1) second each, and then blink green five (5) times twice. The remaining capacity and time is now reset to the
original capacity.
Changing the Batteries
1. Open the top of the Filter Monitor unit and remove and discard the used batteries.
2. Insert two (2) fresh AAA batteries into the battery compartment, making sure to match the + and – signs. Close the
battery compartment.
3. There will be a long audio sound, and the leD will blink green for two seconds, and then blink green five times.
4. After installing the batteries, press the check/reset button to confirm the leD is functioning.
4.4: Resetting the Capacity Monitor or Changing the Batteries
4.5: Flushing / Disinfecting the System
5.1: Warranty
Multipure recommends that you not allow water to sit in the system for extended periods of time without use. If a unit is left
unused for more than 10 days, it may need to be flushed / disinfected before resuming normal use.
1. remove the filter by following the directions in 4.2: Removing the Old Filter.
2. Add 5 to 7 drops of bleach to the bottom half of the system.
3. reconnect the top half of the housing without a replacement filter installed.
4. Turn on the water supply and allow the system to fill up with the water/bleach solution.
a. Countertop systems:
i. Turn on the faucet, and press the right button on the diverter valve to select the filtered water spout.
ii. Once water begins to flow, press the left button to stop the filtered water spout.
iii. Turn off the faucet, and let the system soak for at least 30 minutes.
b. Below-sink systems:
i. remove the faucet spout and place it in a container with one quart of water and bleach (5 drops of bleach
per one quart of water).
ii. Allow the system and the faucet to soak for at least 30 minutes.
iii. Clean the inside of the faucet spout with pipe cleaners. You may also use a mild detergent, such as soft scrub®.
5. Flush and rinse the system.
a. Countertop systems:
i. with the faucet off, press the right button on the diverter valve to select the filtered water spout.
ii. let the water and bleach flush out of the system until the water flow stops.
iii. Open, clean, and rinse out the inside of the system housing.
iv. Follow the directions in 1.1: Installing the Filter Cartridge (Universal).
v. Follow the directions in 2.2: Preparing and Operating Your Drinking Water System.
b. Below-sink systems:
i. Disassemble the system housing and pour out the water/bleach solution. Clean and rinse out the inside of the
system housing.
ii. Follow the directions in 4.3: Installing the New Filter.
Multipure 90-Day Guarantee: Multipure is confident in the performance of its Drinking water systems (Dws). If you
should find this Drinking water system unsatisfactory, let us know within 90 days of purchase for a prompt exchange or
refund.
Multipure Warranty: Multipure warrants to the original retail customer its Dws and components to be free of defects in
material and workmanship for use under normal care, and will repair or replace any system at no charge (excluding trans-
portation to Multipure Corporate Headquarters) to the customer during the warranty period. The Dws housing is warranted
for a lifetime (provided the filter has been changed at least once per year); all exterior hoses and attachments to the Dws
are also warranted for defects in material and workmanship for one (1) year.
Multipure solid Carbon Block Filters are warranted for defects in material and workmanship for use under normal care. The
capacity of the filter cartridge depends upon the amount of impurities in the water to be processed.
except as otherwise expressly provided above, Multipure makes no warranties, express or implied, arising by law or other-
wise, including without limitation the implied warranties of merchantability and fitness for a particular purpose, to any per-
son. This limited warranted may not be altered, varied, or extended except by a written instrument executed by Multipure.
The remedy of repair or replacement as provided under this limited warranty is exclusive. In no event shall Multipure be
liable for any consequential or incidental damages to any person whether occasioned by negligence of the manufacturer,
including without limitation damages of loss of use, cost of substitution, property damage, or other monetary loss.
warranty is valid only if the Dws is operated within conditions listed herein. The warranty begins from the date of purchase.
20
5. Additional Information