MTS Series 642 Bend Fixtures User Manual
Page 36
Series 642 Bend Fixtures Product Information
36
Installation
Install Model 642.01, 642.10, and 642.25 Bend Fixtures—Electromechanical
Systems
1. Turn the electromechanical toggle switch to the on position. Position the
crosshead as necessary to allow adequate room to install the bend fixtures.
2. Clean the mating parts on the bend fixtures and the load unit.
3. Insert the adapter into the load unit component (force transducer, attachment
fixture, lower mounting fixture, and so forth). Align the holes in the adapter
and the load unit component and insert the pin.
4. Preload this connection by tightening the locknut bearing on the adapter
against the surface of the load unit component. Tighten sufficiently to
ensure that there is no slack during testing.
5. Set the bend fixture on the adapter, align the bend fixture, and secure the
bend fixture to the adapter using the supplied socket head cap screw.
6. Repeat Step 5 for the other bend fixture.
Model 642.01, 642.10, and 642.25 Bend Fixtures
Socket Head Cap
Screw
Adapter
Locknut Bearing
Load Unit
Component
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)