JUMO 60.3035 Surface-mounting single or twin thermostat, ATH-SW Data Sheet - Manual (Page 4)

2013-03-12/00376440
Data Sheet 603035 Page 4/9
JUMO GmbH & Co. KG
Delivery address: Mackenrodtstraße 14
36039 Fulda, Germany
Postal address: 36035 Fulda, Germany
Phone: +49 661 6003-0
Fax: +49 661 6003-607
E-mail: [email protected]
Internet: www.jumo.net
JUMO Instrument Co. Ltd.
JUMO House
Temple Bank, Riverway
Harlow, Essex CM20 2DY, UK
Phone: +44 1279 635533
Fax:
+44 1279 635262
E-mail: [email protected]
Internet: www.jumo.co.uk
JUMO Process Control, Inc.
6733 Myers Road
East Syracuse, NY 13057, USA
Phone: 315-437-5866
1-800-554-5866
Fax: 315-437-5860
E-mail: [email protected]
Internet: www.jumousa.com
Ambient temperature influ-
ence referring to the control /
limit value range
When the ambient temperature on the case deviates from the calibration ambient temperature 22 °C,
a switch point offset occurs.
Higher ambient temperatures = lower switching point
Lower ambient temperature = higher switching point
Add-on thermostats with scale limit value
< 200 °C ≥ 200 °C ≤ 350 °C > 350 °C ≤ 500 °C
TW STB/STW (STB) TW STB/STW (STB) TW STB/STW (STB)
Influence on the switch head
0.08%/K 0.17%/K 0.06%/K 0.13%/K 0.14%/K 0.12%/K
Influence on the capillary per metre
0.047%/K 0.054%/K 0.09%/K 0.11%/K 0.04%/K 0.03%/K
admissible ambient tempera-
ture for use
max. +80 °C
admissible storage tempera-
ture -50 to +50 °C
Rated position any
Case
standard Aluminum die casting, painted
Set point adjustment The switching point can be adjusted by means of a screwdriver once the case lid has been removed
Protection class EN 60 529-IP 65
Cable inlet Cable screw connection M 20 x 1.5, sealing area 6-12 mm
Switch head is fastened
Type series ATHf-SW
with capillary
with 2 screws through the case bottom part (wall mounting),
lateral capillary outlet in the case.
Weight approx. 1.2 kg
Process connection a
a For different process connections and sheaths, refer to data sheet 606710.
Type series ATHs-SW
with rigid shaft Scale limit value up to 150 °C
sheath "20“
Scale limit value over 150 °C
sheath "30“
Screw-in sleeve with screw-in spigot G 1/2
form A as per DIN 3852/2
Screw-in sleeve with screw-in journal G 1/2
form A as per DIN 3852/2 and intermediate piece,
to ensure that the max. admissible ambient tempera-
ture of +80 °C is not exceeded on the case
Type series ATHf-SW
with capillary plain cylindrical probe "10“ as standard
Screw-in sheath "20“ on request
Screw-in sleeve with screw-in spigot G 1/2 form A as per DIN 3852/2
and clamping piece with locking screw to lock the probe
Material Sheath "20“ Sheath "30“
up to +150 °C CuZn as a standard
over +150 °C CrNi
over +150 °C CrNi
Fitting length S Standard lengths: 100, 120, 150, 200 or 300 mm
different lengths on request
Immersion tube ∅ Single thermostat D = 8 mm Double thermostat D = 15 mm