Gamber-Johnson 7160-0448 - Manual

INSTALLATION INSTRUCTIONS
Product Revision Form
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Rev.A INST-583
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© copyright 2012 Gamber-Johnson, LLC
Printing Spec: PS-001
VISOR MOUNTS - CAPRICE
7160-0448, 7160-0449
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
The Caprice Visor Mounts 7160‐0448 & 7160‐0449 provide the user with the capability to secure a mobile
camera to the passenger side visor. Each system includes a Max
3 all axis knuckle that allows the user to
orient the camera in several positions. The 7160‐0448 mount, includes a second knuckle to mount a display.
Tools Needed Material Needed
5/64‐in Hex wrench (Allen wrench) #10 Self drilling screws
3/16‐in Hex wrench (Allen wrench)
Small Flat Screwdriver or Knife
Installation
1. Remove the passenger side visor retainer clip near the center of the vehicle headliner. The clip is
assembled with a wedge/pin which must be pried out with a small flat screwdriver or knife blade.
Also remove the metal clip inserted into the cutout in the headliner. Refer to FIG 1, 2 & 3.
2. Reassemble the metal clip and the visor retainer clip to the plate supplied with the Caprice Visor
Mount Assembly.
3. Position the Visor Mount Assembly over the cutout in the headliner so the metal clip extends into
the headliner cutout FIG 5.
4. Secure the Visor Mount to the headliner using a minimum of four self‐tapping fasteners FIG 4 & 5.
a. Self‐tapping fasteners are not supplied.
b. Caution: Self tapping fasteners that are too long may go through roof of vehicle.
5. Secure the camera to the front camera bracket using (2) ¼‐20 x .50 socket button head cap screw,
(2) ¼‐in lock washer, and (4) ¼‐in nylon flat washers. Refer to FIG 4.
6. Position the camera as desired.
7. Secure the display to the display bracket using hardware supplied by the display manufacturer
(7160‐0448 units).
8. Insert and tighten #10‐32 socket head set screws to lock the Max 3 knuckles in place.
1 / 2