American Lighting LED Tape-Rope Hybrid - Manual

LED Tape-Rope Hybrid
Safety instructions for 120-TL-60-3.3, 120-TL-60-6.6, 120-TL-60-13.2, 120-TL-60-19.7, 120-TL-60-32.8
and 120-TL-60-45.9 for all colors: BL = Blue, GR - Green, RE = Red, WH = Bright White, WW = Warm White
www.americanlighting.com
WARNING: These products may represent a possible shock or fire hazard if improperly installed or attached in any way.
Products should be installed in accordance with these instructions, current electrical codes and/or the current
National Electric Code (NEC). Use this product only with factory recommended power cords that are supplied with the
kit.
Before use, note that this product requires an 120V AC outlet. Ensure that the voltage of your power supply is
compatible! Any other power source or feed may damage the product.
IMPORTANT SAFETY INSTRUCTIONS -
Read and follow all safety instructions and save for reference.
1. Do not cover this product with anything that impedes the necessary
heat dissipation. Covering may cause the Tape-Rope to overheat and
melt or ignite.
2. Do not place Tape-Rope Light in a groove or routed channel.
3. Do not plug in or operate the Tape-Rope Light if it is tightly coiled.
4. Do not route the cord or cable through walls, doors, windows or
any like part of a building structure.
5. Do not use if there is any damage to the Tape-Rope Light’s outer PVC
housing or the cord’s insulation. Inspect Tape-Rope Hybrid Light before use
and periodically for any damage to PVC and cords.
6. Do not submerge Tape-Rope Light in liquids, or use the product in the vicinity of standing water or liquids.
7. Secure Tape-Rope Light using only the mounting clips provided or with factory recommended track (item
120-TL-TRACK-4, sold separately). Do not secure this product or its power cord with staples, nails or like
means that can damage the outer PVC housing or the cord’s insulation. Discard any Tape-Rope Hybrid
Light that has a broken outer jacket or frayed wire insulation.
8. Do not subject Tape-Rope to continuous flexing. Do not install Tape-Rope Hybrid Light on gates or doors.
9. All units must be disconnected from power during installation and before adding additional length or
otherwise disconnecting sections for any reason.
10. Do not exceed the maximum run length as noted by the tag on the cord: 106 feet for all colors, except
211 feet for Red. Note: The markings along the product body are production markings. They are not maximum
run lengths!
11. Do not install in tanks or enclosures where heat cannot dissipate when Tape-Rope is on.
12. Follow these instructions carefully when connecting Tape-Rope sections and/or attaching power cords.
Ensure that all connections, including the end cap on the last segment, are properly tightened. For
outdoor applications, use dielectric grease and shrink tube to preclude the entrance of water.
13. Risk of fire. Do not replace attachment plug. Discard and replace product if attachment plug is damaged.
14. This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of
electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension
cord unless plug can be fully inserted. Do not alter plug.
15. This product is designed for decorative use only. Not to be used by children as a toy. Keep out of reach of
small children.
RV1326
Do not operate rope light
while it is tightly coiled.
NOTE: Cutting the Tape-Rope Hybrid and/or altering the power cord in any way including, but not
limited to, cutting, splicing and/or adding any power accessories will void the ETL Listing.