beautypg.com

2 before operating (cont.), 3 operation safety, 4 pto safety – Echo 71854 User Manual

Page 6

background image

PTO CHIPPERS

4

SAFETY

read and follow instructions on PTO safety decals.

1.

Stay alert and pay attention when PTO is operating.

2.

Keep bystanders, especially children, away from PTO

3.

driveline.
check the driveline to ensure it is attached securely

4.

to the power supply.
Keep guards and shields in place at all times while

5.

operating. disengage PTO, shut off power source, and

make sure all moving parts have come to a complete

stop before removing guards or shields.
clothing worn by operator must be fairly tight. Never

6.

wear loose fitted jackets, shirts, or pants when work-

ing around the PTO. Tie long hair back or put under

a cap.
Keep hydraulic hoses, electric cords, chains and other

7.

items from contacting the driveline.
do not exceed the recommended 540 rPM PTO op-

8.

erating speed.
Before inspecting or servicing the PTO drive area,

9.

disengage the driveline, shut off power source, discon-

nect spark plug wire from spark plug and make sure all

moving parts have come to a complete stop.
Keep hands, feet, and clothing away from all PTO drive

10.

parts.
do not clean, lu-

11.

bricate or adjust

the PTO shaft

when it is run-

ning.

Shut off machine immediately if the machine becomes

12.

clogged, the cutting mechanism strikes any foreign

object, or the machine starts vibrating or making an

unusual noise. Shut off the machine, disconnect the

battery, remove the ignition key and make sure all

moving parts have come to a complete stop. after

machine stops:

inspect for damage.

a.

replace or repair any damaged parts.

B.

check for and tighten any loose parts.

c.

check blade bolts for proper torque after every 8 hours

13.

of operation. check blades and rotate or resharpen

daily or as required to keep blades sharp. failure to do

so may cause poor performance, damage or personal

injury and will void the machine warranty.

always stand clear of discharge area

1.

when operating this machine. Keep

face and body away from feed and

discharge openings.
Keep hands and feet out of feed and

2.

discharge openings while machine

is operating to avoid serious personal injury. Stop

and allow machine to come to a complete stop before

clearing obstructions.
Set up your work site so you are not endangering traffic

3.

and the public. Take great care to provide adequate

warnings.
do not climb on machine when operating. Keep proper

4.

balance and footing at all times.
check cutting chamber to verify it is empty before

5.

starting the machine.
The disk will continue to rotate when belt is disen-

6.

gaged.
do not insert branches larger than 8 inches in diameter

7.

into chipper or machine damage may occur.
When feeding material into machine, do not allow

8.

metal, rocks, bottles, cans or any other foreign material

to be fed into the machine.
ensure debris does not blow into traffic, parked cars,

9.

or pedestrians.
Keep the machine clear of debris and other accumula-

10.

tions.
do not allow processed material to build up in the

11.

discharge area. This may prevent proper discharge

and can result in kickback of material through the feed

opening.

1.3 oPeraTion saFeTY

Before inspecting or servicing any part

13.

of this machine, disengage PTO, shut

off tractor engine, and make sure all

moving parts have come to a complete

stop.
check that all screws, nuts, bolts, and

14.

other fasteners are secured, tightened and in proper

working condition before starting the machine and once

every 8 hours of operation.
do not transport or move machine

15.

while the machine is operating or

running.

1.2 beFore oPeraTing (conT.)

1.4 PTo saFeTY

This manual is related to the following products: