Advance Adapters 712563 - Manual

ADVANCE ADAPTERS INC. P/N: 712563
P.O. Box 247, 4320 Aerotech Center Way New Item: (08/06)
Paso Robles, CA 93447 PAGE 1 OF 3
Telephone: (800) 350-2223 Fax: (805) 238-4201 REV DATE: 07-31-10
SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the
components will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion,
we strongly recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter
components. We recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment.
These manuals are normally available at automotive dealerships and parts stores.
KIT CONSITS OF:
No: Qty Part No. Description
OPTIONAL ITEMS:
AX15 5 SPEED TRANSMISSION RETRO-FIT
FOR THE AX5 4 CYL. 5 SPEED EXT. SLAVE
1. 1 712563-PLT AX15 ADAPTER PLATE
2. 1 712563-RET T/O BEARING SNOUT
3. 1 712563-S SHIFT TOWER SPACER
4. 1 712590-C T/O BEARING ASSY.
5. 4 715523-SP CROSSMEMBER SPACERS
6. 2 716086 AX5 BELLHOUSING DOWEL PIN
7. 1 716167 .750 PILOT BUSHING (AX15 1995 & Newer)
8. 1 716742 AX15 SEAL
9. 4 720037 10mm-1.5 x 35mm H.H.C.S. (Crossmember)
10. 2 720039 10mm-1.25 x 20mm S.H.C.S(bell by slave cyl)
10. 4 720066 8mm-1.25 x 35mm S.H.C.S. (Shifter Bolts)
11. 13 720091 10mm-1.25 x 24mm S.H.C.S.
12. 2 720092 8mm-1.25 x 24mm S.H.C.S.
13. 4 723103 LOCK WASHER (Retainer)
14. 4 723113 5/16"-18 x 7/8" S.H.C.S. (Retainer)
15. 1 383824 1-1/8" 10 SPLINE DISC (CF382438)
INSTALLATION NOTES:
This kit is designed to fit the 1995 and newer AX15 transmission. Earlier model
transmissions can use a stock pilot bushing, one with a .590" I.D. We
recommend that the stock flywheel be removed and
resurfaced at a machine shop. A new clutch disc
and release bearing has been provided in this kit. A new
pressure plate is also recommended before installing your new transmission. We offer
a Centerforce pressure plate,
Part No. CF361914
.
Before disposing of the old AX5 transmission, you will need to retain the shifter housing
from that transmission. You will also be using the stock 4 cylinder bellhousing and stock
release arm and crossmember mount.
The transfer case must have a new input gear installed to fit to the AX15 transmission. If retaining the NP231 transfer case
and because the new transmission is longer, we highly recommend a fixed yoke kit to be installed during this transmission
swap. This will allow for a new, longer rear drive shaft. The Atlas 2 speed or 4 speed transfer cases are also an excellent
upgrade to your Jeep, and this would be the perfect time for this additional upgrade.
ASSEMBLY PROCEDURES:
1. Refer to a service manual for the removal of the stock AX5 transmission. Also remove the pressure plate, disc, and
flywheel.
The AX5 transmission was coupled to a
21 spline transfer case. The AX15 trans-
mission has a 23 output shaft. When
upgrading your transmission, you will
also be required to change out the input
gear of the transfer case.
716054 1987-1994 NP231 T/Cs
716095 1995-2006 NP231 T/Cs
716096 NP207 T/Cs
The transfer case shifter braket must also
be changed.
Jeep YJs
P/N 715545
Jeep TJs P/N 715542